Search results for query: *

  • Users: dilley340
  • Content: Threads
  • Order by date
  1. dilley340

    Two car shows in Howell, MI - Post 2 of 2 - Image heavy

    The second show was at St. John Catholic Church. There were more Mopars at this show. I didn't meet anyone, but maybe you'll recognize the cars.
  2. dilley340

    Two car shows in Howell, MI - Post 1 of 2 - Image heavy

    The first show was at Roy's Autoworks. There were only a handful of Mopars at this show. I didn't meet anyone, but maybe you'll recognize the cars. Man, this shop was clean. I threw in a few non-Mopar cars too... please forgive.
  3. dilley340

    Going to be a cold one tonight...

    Here in Howell, Michigan right now (7:50 PM) ...
  4. dilley340

    Show me your underhood fuel line(s) setup

    I'm looking for ideas on how you guys ran your fuel line(s) from an electric pump up into the engine bay and then to the carb(s). Thanks.
  5. dilley340

    Looking for speaker recommendations for '74 Sport's (Jerry) speaker brackets

    I'm going to pick up a dash frame speaker bracket from our own '74 Sport (Jerry) and want to know what speakers you guys have used with his brackets. I'm stereo challenged and looking for suggestions please. It's going in a '73 Duster. Thanks.
  6. dilley340

    AN adapter fitting question

    I'm having trouble with my AN NPT fittings seating into my electric fuel pump and regulator. I can only get 1-2 thread maximum engagement using two different manufacturer's (Aeroquip & Russell) fittings. 3/8" NPT to be exact. I have ran a 3/8" NPT tap through the pumps and regulators and they...
  7. dilley340

    Should I use something on my electrical connectors?

    I'm getting ready to install new wire harness assemblies and was wondering if I should spray some sorta electical connector grease or lube in them. If so, what should I use?
  8. dilley340

    How do I make my dome light fade away when you shut the door?

    I was curious about what it takes to convert my dome light on my '73 Duster to fade-away after you shut the door, just like my Dodge Caravan. Anybody do this before?
  9. dilley340

    3/8" pushrods and SB Edelbrock head clearance

    I'm looking for some input with the clearance needed for 3/8" pushrods and Edelbrock SB heads for my 340. I received my Smith Bros. pushrods and did a mock-up to check for the clearance and found that they rub although not shown in the pics below. What's a safe bore size to open these up?
  10. dilley340

    SB Timing chain indexing question

    In my Hayes repair manual it says to take the #6 piston to TDC on the compression stroke to install my timing chain. Does this sound right... why not #1 piston? At this point I don't have the lifters or pushrods in, so can't I just align the dots on the sprockets?
  11. dilley340

    340 fuel pump eccentric

    Do I need the fuel pump eccentric if I'm using an electric fuel pump? I'm getting ready to put the timing chain on.
  12. dilley340

    Milodon windage tray on a 340 stroker

    Have anyone of you installed a Milodon windage tray on your 340 stroker motor? Mine happens to have Milodon 4-bolt caps. I'm curious about the trimimg or dimpling you had to do for fit and about the possibilty of adding spacers for clearance. Thanks.
  13. dilley340

    Is that you JohnnyJet?

    Picked up the November '07 Mopar Muscle and spied a particular Silver Frost '73 Duster with a 360 and 4-gear on page 82 in the "Homebuilt Cruisers" section.
  14. dilley340

    SB head bolt question

    Do any of the head bolts enter a water jacket on a 340?
Back
Top