Search results for query: *

Just an observation - are you asking for the radio knobs and heater knobs, or the heater knobs and the radio? Your question could be interpreted either way.

Hi, I have a motor; can you provide any photos and your price please Thank you, Michael

Located a radio - thanks to all who responded. Michael

I am looking for a NON-FUNCTIONING AM radio for my Demon. I would like to gut the radio and replace the innards with modern electronics. Cosmetically, anything visible once installed should look presentable.

Hi, Good solution; I had a similar idea: http://www.forabodiesonly.com/mopar/showthread.php?p=1970558389&posted=1#post1970558389 Did you make the tapered guide on a lathe? What material did you use?

Here's where I bought my kit: http://www.engine-swaps.com/Pages/ProductsType/GasketKits.html

Okay, so no additional gasket sealer then? The Schumacher instructions say to use gasket cement on the base gasket "to hold in place", but that's on the underside - they don't mention anything on the top of the base gasket other than the strip caulk.

I like your solution, too. I never thought to put the seal on the table, I was trying to push it down over the shaft. Yours is another idea so good that it seems obvious - after the fact! Did you put any gasket sealer on top of the base gaskets?

I was going to give the hot water a try, but then I thought about using the tapered shaft and that did the trick. I imagine that the hot water would help, but I'd probably burn my hands in the process. ;) Plus, you'd probably have to work quickly before the seal cooled down.

I used dish soap as well...I don't think I could have done it without, even with the tapered shaft. Can't imagine how anybody installs the seals just by hand (with soap or not)

Here's a thread with photos of the grease fittings: http://www.forabodiesonly.com/mopar/showthread.php?t=35796

Glad to help! Yes, I did add the grease fittings. One thing that did concern me though was the possibility that drilling can cause metal chips can get into the assembly. I did my best to blow the chips away as I drilled. Hopefully it won't be a problem.

I bought a Schumacher wiper pivot seal kit for my 71 Demon, and struggled for quite a while to get the water seals on. Then I came up with a solution which worked so well, it now seems obvious. The instructions included in the Schumacher kit say not to use a mechanical spreading device, but I...

When reinstalling the pivots, should I put gasket sealer on top of the base gaskets? Schumacher's instructions do not say to do so, but they do say to use gasket cement on the underside of the gasket.

So...who owns the shared armrests then? Should passengers in the aisle or at the window each get 1.5 armrests, while the middle seat gets only two halves? Is it the luck of the draw? Where does it end?! ;)

I don't disagree... I do wonder what would have happened if the guy simply and politely asked the woman not to recline all the way, instead of forcing the device on her. It might have turned out differently...or not.

Thanks for the suggestion - but what is a "blower motor black vent tube"? (I am assuming that it has a 90 degree bend in it)

I agree with you - reasonable people should compromise and not act like jackasses. Of course the person behind has no more right to be comfortable than the one in front - and no less. That's exactly my point. Your statement: "It's more inconsiderate/selfish to force someone else to be...

Thanks for the reply and photos - I'll have to get some of that foam, and extend the tube as well.

Thanks, looks like I'll need to extend the tube a bit.

My car is originally a non-A/C car, so I have had to modify the firewall to accommodate the A/C heater box (enlarge blower motor hole, add holes for mounting studs, plug one of the insulation nail holes). So far, the only hiccup has been getting the condensate drain tube to line up and...

Thank you for the reply. So, does the copper drain tube simply feed through a grommet then? Also, I noticed that there is almost an inch of space between the back of the heater box and the firewall - and the copper tube on my heater box does not penetrate the firewall; I guess I'll have to...

I am adding factory air to my Demon, and am not clear about the condensate drain setup. I noticed that the 3/8" copper tube does not penetrate the firewall, which leads to my question: what should a properly installed drain tube look like? Is there a rubber grommet, or an elbow of some sort...

When a seat reclines, it affects two people - the one in the seat, and the one behind the person in the seat. Why should only one of them have control? The fact that a device like the Knee Defender even exists is because some people think that having a reclining seat gives them license to be...

Is there a flexible fitting which connects to the condenser drain on the factory air? I am adding factory air to my Demon, and am not clear about the condensate drain setup. I noticed that the 3/8" copper tube does not penetrate the firewall, which leads to my question: what should a properly...

Not a Mopar, but my brother found some old service receipts behind the glove box of his Ford Explorer which had the vehicle's mileage recorded on them. Only problem was that the mileage on the receipts was about 100K higher than the what the odometer showed! He did get the dealer to refund his...

I am looking for a rear speaker/defogger offset adapter. I don't think these were originally available for A-bodies, but they ought to fit. Thanks in advance, Michael

I would like to install rear speakers in my Demon, and I'd also like to put in a rear window defogger. Here's my dilemma - since it appears that the defogger was designed to install in the same place as a speaker, it would seem that I can have either one speaker and a defogger, or two speakers...

Don't forget the General Lee...

When a car is built with a single horn, is it "High" or "Low"? My '71 Demon came from the factory with one horn. I would like to add a second horn, but I don't know whether I'd need the "High" or "Low" to compliment what I've got. (To be clear - when I say "compliment", I would want to add...