Search results for query: *

I’m doing HotRod Dragweek this year in my Demon. We swapped heads and to Isky iron rockers and I’m trying to measure for new pushrods. The engine has a hydraulic .509 in it and I can’t seem to find the pre-load number for the lifters anywhere. Can someone please tell me what it is supposed to be?

The fender extensions on my 1972 Demon are fiberglass, I believe they're from a set of 1971 Demon fenders. I need to know if anyone knows if either of these studs listed on year one will fit them to bolt them to the fenders I'd appreciate some help. 1966-74 A B E-Body Dual Hood Scoop Stud 1971...

I’m installing a Holley Stealth Super Sniper 550-877 FI kit and need a clean 12v switched source that is hot cranking and running. Instructions specifically say not to use the ignition coil, audio systems etc. where can I pull this from?

I have a few parts from some 400’s I don’t need. All parts are sold as seen in pics. Some of this stuff may have no value and if it doesn’t sell I will just scrap it but figured I’d offer the stuff up before I scrap any of it. I will post pics of stuff if you want more pics feel free to ask...

I have two sets of C body spool mounts from 400’s they will include the bolts and are as removed from engine $50/shipped a set. I personally would replace the rubber mounts but I’ll let you decide if they’re ok.

I parted a 1972 Dodge Dart it is stripped at this point so parts can be boxed and shipped quickly. Shipping costs are not included in prices. Prices negotiable. Located in Martinsville, Indiana. Make offers worst I’ll say is no. The only parts that remain are listed below. 72 Dart Side...

I need the plastic bezel that covers the heater controls, non wood grain 1972 Dart. This is the one I need minus the controls, I have all of that.

My front “bowl” on my master cylinder is empty does it feed fronts or rears? The pictured master cylinder is a 72 Demon that has a stock proportioning valve in it.

I parted a 1972 Dodge Dart it is stripped at this point so parts can be boxed and shipped quickly. Shipping costs are not included in prices. Prices negotiable. Located in Martinsville, Indiana. Make offers worst I’ll say is no. 72 Dart Side windows rear $100 pair Dual horns $50 Windshield...

I parted a 1972 Dodge Dart it is stripped at this point so parts can be boxed and shipped quickly. Shipping costs are not included in prices. Prices negotiable but don’t be insulting. 72 Dart Side windows rear $100 pair Dual horns $50 Windshield trim $150 Rear Window trim $50 sides/top only...

I am approaching a point in which I am considering redoing the entire wiring system in my Demon. It currently has a mixture of factory, CrackedBack’s MSD and my wiring. So none of the factory ignition wiring is used nor is the voltage regulator or alternator wiring is used. I have two BlueSea...

I am approaching a point in which I am considering redoing the entire wiring system in my Demon. It currently has a mixture of factory, CrackedBack’s MSD and my wiring. So none of the factory ignition wiring is used nor is the voltage regulator or alternator wiring is used. I have two BlueSea...

BB Demon and I have switched the water pump housing and radiator. The top hose now goes to passenger side and the bottom to drivers side. Does anyone know what hoses I should get?

I am parting a 1972 Dodge Dart it has been stripped and crushed at this point but I saved all I could, parts can be boxed and shipped quickly. Shipping costs are not included in prices. Prices may be negotiable. Large parts can be picked up in Martinsville or Greenwood Indiana depending on if...

What are the little clips that hold the hood hinges onto their pins called? I need some but I’m not sure what to search for.

i was reinstalling the torque converter in the trans and heard a sizzling and saw this connection smoking, so I grabbed a rag and pulled it apart. What is the best way to fix this? I am pretty sure it is the main feed for the dash.

I’m trying to order a Dakota digital temperature sensor for my electric fan controller and have had no luck finding someone that can tell me which one will fit my big block housing. So two questions, Firstly where does it go? Second anyone have a part number for the correct one? I know for a...

I am in need of the following steel parts. I do not want NOS parts as I can't afford them. If I can't find reasonably priced parts I'll just keep what I have. Would prefer they be near Indiana. 1972 Dart- Front fenders hood lower valance Possibly a grille as mine is damaged 1972 Duster- deck...

I am wanting to wire some 12v keyed accessories in my Demon. What I would like to do is add a blue sea fuse box and run the 12v keyed source to it and then utilize the power through the new fuse box. Is there any reason I can’t do this? Where would you draw this keyed power from? Is there a...

I have a 72 Demon that is getting Wilwood kit 140-11022 D. I have begun the install and wanted to put up some info that I have found and post pics to help those looking at this kit. First the backside of the spindle that needs ground to clear the new caliper bracket needs to be cut in about...

If you need stuff give this guy a call, he wants car gone in the next month, lots of good parts. Vast majority of interior is gone including the following... seats, all door panels, upper fronts, handle cups, drivers door mirror. PM for number.

Will the seats from a 73 Scamp bolt in and look right in a 73 Duster? What would you pay for them? Back seat appears to be in great shape front is reported to need recovered.

I need a front bench seat and possibly a rear seat for a 73 Duster. As close as possible to Indiana. Also need the upper door trim parts (plastic)for a 73 Duster prefer blue but will consider any color.

Still trying to decide on an aluminum radiator and saw these guys, anyone use them? 1" tubes sound good to me. http://www.speedcooling.com/26-Big-Block-Mopar-Radiator.html

I have a 73 Duster, buying it from a buddy. It has the hood latch support "t" out of it and I cant find any of the bolts, neither can my buddy. Can someone help me by measuring them and letting me know the sizes. I need both the ones for the top and where it bolts to "core support"

Want to buy a set of Moroso anodized aluminum valve covers. I don't really care about the color, I have a gold air cleaner but it will all be changed to match regardless of color.

I have a Holley #9834-1 for sale Needs rebuilt Complete In Indiana asking $100 OBO More Pics

I have a Holley #1850-2 for sale Choke horn damaged, appears to have been dropped. Would explain why choke plate is out. Needs rebuilt and sight screws and I believe that is all. Will come with at least a partial (maybe complete?) Holley trickit #37-720 Choke rod removed (I don't have it but...

I have a Holley 750 Dbl. pumper #4779 for sale Needs rebuilt and two butterfly plates, sight screws and I believe that is all. Choke plate and rod removed (I don't have them) In Indiana asking $125 OBO More pics

So I'm trying to help a buddy out that has this 73 Duster. When he got it the ignition key and cylinder were in column, it got lost he and a buddy "tool it out" so they could free steering to move car. I am a week away from having engine back together and ready to run and want it to fire from...