Search results for query: *

1968 440 hp engine with a 727. Engine is stuck from sitting I believe. Looks pretty complete aside from the air cleaner. Cash or PayPal only. Willing to trade for 5.7 hemi stuff or complete two post car lift. 2500$ Located in casstown Ohio 45312

Mopar A body a833 OD 4 speed transmission. Cleaned and rebuilt with brewers performance synchros, gaskets, seals, and needle bearings. Input shaft retainer has been dimpled to use an American powertrain hydraulic throwout bearing, but a traditional throwout setup can still be used. The...

I’ve got a bunch of stuff free for pickup in Huber heights Ohio 45424. Six pack base is a bad molding the carb holes are too big. If you’re handy with fiberglass you could fix. Limited slip clutch plates were purchased for a 9.25 but probably work with other setups. Vband clamp is 2.5 diameter...

Hey FABO, I’ve got some parts leftover from my 1983 dodge w150 build that I didn’t end up using. All new never used. Free for pickup in Huber heights, Ohio 45424. Please check pics for part numbers. I have this posted on ram charger central but there was no interest there. Figure I’ll post them...

Center carb is list number 4792~340 six pack. Outboard carbs are list number 4365~440 six pack. One of the outboards doesn't have a list number stamped. I included a picture inside the horn of both outboards to show the center body casting numbers are the same between the two (D-1565 and...

Hello Fabo, I have an Autometer programmable fuel quantity gauge (great for aftermarket sending units where the ohm range is not the same as factory) for sale along with the corresponding gauge panel. Worked great. What you see in the pictures is what’s for sale. A little dusty from sitting on...

Hello fabo, I have a set of rally gauges out of my 1968 barracuda dash for sale. This is just for the set of 4 gauges. 100.00 shipped in the lower 48

Hello Fabo, I have a set of Autometer oil pressure, coolant temperature, and volt gauges along with the matching panel for sale. Electric sending units (not included). What you see in the pictures is what is for sale. Worked great just a little dusty from sitting on my shelf, I replaced them due...

I want to kick this thread off by saying this is for entertainment purposes only. What you use this information for is completely your responsibility. I take no responsibility for your actions. With that taken care of, this is how I swapped Autometer gauges into the 1969 Plymouth Barracuda...

Hey fabo, I’ve gotten so many good deals from members on here I'm thinking it’s my turn to pay forward. I’ve got a set of what I believe to be 15x7 steel wheels that I removed from an 80’s Chrysler out of a junkyard a few years ago. They have a set of ancient defender sport 235/60r15 and...

Hey Fabo, I’ve got a set of cylinder heads off a late 72 production year 340 for sale. Last three casting numbers are 587. 250$ shipped in the lower 48. Thanks for looking!

Hi fabo! I’ve got numerous parts off the 1972 340 I purchased late last year. First is the intake, carter thermoquad carburetor, and their related parts. Casting number for the intake is 3671918 with a date of 2-7-73, and the carburetors casting number is 6319s with a date of 08 1 3. Much like...

Looking for a set of used sb 2.02 intake and 1.60 exhaust valves. Preferably factory pieces. Need to be able to use them with only a lap. Possibly interested in new for the right price.

Hi fabo, I’m looking for a set of two early 10.5 compression std bore factory 340 pistons. Would be interested in a set of 8 if the price is right.

A pair of bbp spacers. Slight damage to the countersinks on both (shown in pics). 55$ shipped in the lower 48

Hey guys, I have a reproduction Grant tuff wheel and adapter I don’t need. Nice shape overall. Splines look good. Kicker is something between the wheel and adapter would occasionally make a clicking noise while making turns. Ended up putting JB weld between each layer of the adapter/wheel to...

Hey Fabo, I have a SBM Edelbrock pro flo 4 efi setup with tablet that I no longer need. P/N 35900. It’s all brand new. Any parts that came in bags have remained unopened. I taped up the intake so nothing could get in it while it was sitting on my shelf. I threw away the original box to conserve...

Brand new never used Edelbrock universal efi fuel sump kit P/N 36031. Opened box just to inspect the parts. Plans have changed and I no longer have a need for it. Goes for 405.95+tax on summit racing. Edelbrock Universal EFI Sump Fuel Systems 36031 Asking 350$ shipped in the lower 48. Thanks...

Has anyone been able to source a reasonably priced set of new axle shafts for an A body 8.25? Tons of options for jeeps and dakotas, none for the early stuff that I can find at least.

Hello fabo! I have a pair of 73+ Calipers with Fmj hoses (for rear caliper mount application), corresponding brake pads with hardware, and 10.95 caliper brackets. The calipers were purchased reman around 3-4 years ago. Reason for removal is I upgraded to Porsche calipers. 105$ shipped in the...

Hi fabo, i have a set of 10x2.5 rear drums off my 8.25. Reason for removal was I upgraded to Jeep disk brakes. Ready to install and run as is. Or to make it nicer, install better quality shoes. Also it appears to have two different sized bottom springs. I rebuilt these around 3-4 years ago and...

I want to kick this off by saying this thread is for entertainment purposes only. What you use this information for is completely your responsibility. I take no responsibility for your actions. With that out of the way. This is how I swapped 4 piston Porsche brembo calipers onto my 1973...

850$ shipped in the lower 48 Hey everyone, I have a Ford 9 inch differential with a 3.50 Gear Ratio limited slip center section for sale. Comes with the housing, 28 spline limited slip center section, and two 28 spline axles. Spinning the center section over by hand, I do not hear any abnormal...

Looking for a set of 2.02 intake and 1.60 exhaust valves for my j heads. Have to be in useable shape as is.

Hey everyone, I have an apex wheel and tire setup off my 2018 Subaru wrx that I sold. These have the same bolt pattern as the mopar big bolt pattern (5x4.5). I installed these on my duster that had a factory A body width 8.25 with an 1.5 inch spacer just to get an idea of how they look. Front...

Hey everyone, Ive installed a pac-2750 fan controller to run my ford contour fans and I’m having a blinking red light in the top hand left side of the lcd screen whenever I hold sw1. I can’t find anything online explaining what this means and it’s not mentioned in the troubleshooting section of...

Looking for a 67-69 floor shift manual steering A body column. Doesn’t have to be in perfect shape just serviceable. Thanks fabo!

I have what I believe to be an F body mopar (not A body sorry) clutch pedal assembly, Z bar, clutch pedal to z bar rod, bellhousing z bar stud bracket, and z bar to clutch fork rod. 250$ obo shipped in the lower 48. It’s responsibility of the buyer to verify fit and application. Thanks again fabo!

Mopar slant six intake/exhaust manifolds Not mine, seems like a good deal if it’s real (don’t know super six setups)/not damaged.

Not sure if it’s been posted here yet, but jegs is running a sale right now. I’m seriously thinking about picking up a set of bare engine quest heads...