Search results for query: *

Pending sale

Price reduction to $125.00

Three row.

A few more photos.

There are two inlet locations on stock slant radiators. This one which goes from the thermostat housing straight to the inlet with essentially a 90 degree hose. The one I had Champion make for me is the other style with the inlet offset more to the passenger side to use the “S” style hose to...

I have two factory cast iron single barrel stock intakes. $50.00 each plus shipping Located in Nashville, TN

Champion aluminum slant six radiator. 22” core. Used only for one year then pulled and stored. $150.00 plus shipping Located in Nashville, TN

Factory super six intake $200.00 plus shipping Located in Nashville, TN

Looking for a set of verified working HI/LO two horn set up

SSD for the win. Thank you sir. It is disappointing that they put the slant 6 as an option on their website for that thermostat. I am happy with the pump so far. I’ll go back with the trusty super stant when I take off my now sanded housing to repaint.

Just confirmed the housing is original. Part number 2121524. Going to call flowkooler Monday

Other than the change from a standard style to the high flow style, they appear the same and measure the same except for the thickness of the lip that goes in the recessed grove of the housing. I didn’t want to start shaving away metal if there is another housing option out there or even at this...

It’s back together with the Stant thermostat I had. Before I take it back apart I was looking for opinions so I could have the fix and make it a couple hour job I know where to stick the pointy end lol. It’s into the housing. The chart says I’ve bought the right one. The issue is the depth of...

Picked up a flowkooler water pump and high flow 180 thermostat for the slant from flowkooler.com. The water pump install went in seamlessly. When I went to install the thermostat, I found it would not fit. First, the base would not fit into the motor. No problem, a few quick swipes from a file...

Putting seats back in the Dart this evening and noticed one seat had its clip and the other did not. Not sure if these are purely to hold the cable from sagging or helps with kickback. I’ve attached a photo if anyone has one or knows where to find one.

I've not been to that track. It's close so looks like I'll have to put it on the list of things to do this year.

<------- Homestead in Gallatin, TN. Work in Mt. Juliet, TN. If i get the A/C running this year may see a lot more of the Dart running up and down 109 this year.

I'm missing a few clips that hold the metal trim to the rooftop that clips over the edge of the headliner. 8 clips should do it. Nashville area

need a decent set of door and quarter edge moldings where the edge meets the glass. Driver side needed, would by both sides as a package if available. Nashville area.

looing for a good used windshield in my area of Nashville TN.

Driver side, door location? Or driver side, quarter glass location? Thanks

Can you post the mopar part numbers? I have a pair that are too long.

Price reduction $200

That's a lot of info to digest. Hopefully when we get some good weather in Ohio soon I can run it through its paces.

Eastern Gateway Community College (EGCC) 17th Annual Car and Bike Show Sat 4/30/2016 12pm-4pm Registration: 10am-1pm Entry: $5.00 4000 Sunset Blvd. Steubenville, OH 43952 This is an amateur judged show, 25+ awards, 100 dash plaques. See website for directions, all brands & years are...

Everything is stock in my motor. I am assuming from other posts I've read to start at 5^ BTDC and work form there with the vac advance disconnected and plugged at the carb. Ideally end up between 7^ and 8^ BTDC. I've got a piston stop tool to find true top dead center just in case the balancer...

Just finished the motor swap on my '67 Dart. Swapped in a slant six from a '69 Dart. Currently I have the carter two barrel super six set up. Distributor is stock with points. When I got the motor it was two teeth out of time. Getting ready to work on the timing and wanted to know best...

Price reduction. $300.00 OBO

I'll miss Carlile, but definitely will be at the Nats in Columbus.

New motor in and ready for touch up. Biggest help on this install was the tip to jack up the rear end for the motor and trans to slide in easily as a pair. Couple of ground wires, adjustment of the kickdown linkage, throttle cable swap, install the radiator and transmission lines, and a few...