Search results for query: *

JPAR Thanks for your thoughts, however, for my build I have already planned and budgeted for a shop to perform this work. You are correct in the assumption that I don't have the space and very limited time. With starting a family my time will get less and less for this so I would rather have...

Hello, Does anyone have a recommendation for a transmission builder near Portland Oregon? I dropped my 727 small block with some nice parts off with A1 Performance 5 weeks ago, and they are requesting another 3-4 weeks to complete it. They were upfront with me about their lead time (6 weeks...

I currently have a 72 Duster, I ordered and installed a Hotchkiss suspension system TVS for the 68 thru 72. During the installation the sway bar wouldn't fit. After looking at the engine mounts it was assumed that somebody during it's lifetime had swapped a 73+ front K Member. This would also...

Any Chance of getting a preliminary Dyno Sheet?

Selling a set of Schumacher BB Conversion Headers in Chrome, Brand New in Box. Asking $600 shipped anywhere in the lower 48. Accept Paypal. These are the HC Chrome that retail for $695 shipped, but they are currently out of stock. Relist due to Buyer not making payment.

Selling a Edelbrock Performer 2186 Intake Manifold. Has been bead blasted. Asking $160 Shipped to Lower 48.

This is a conversion for B Block to a single wire alternator. Comes with Alternator, bracket, and hardware. This is a v-Belt style so you can keep your current accessories. Asking $100 Shipped to the Lower 48. Accept Paypal.

Selling a set of Schumacher BB Conversion Headers in Chrome, Brand New in Box. Asking $600 shipped anywhere in the lower 48. Accept Paypal. These are the HC Chrome that retail for $695 shipped, but they are currently out of stock.

Selling a set of Schumacher BB Conversion Headers in Chrome, Brand New in Box. Asking $600 shipped anywhere in the lower 48. Accept Paypal. These are the HC Chrome that retail for $695 shipped, but they are currently out of stock.

Bob, Yes the Mag checked out for the block and heads. The bores will need to be cleaned up, I'm not sure what that entails. That being said, I'm not interested in shipping at this time. Done that previously with a block and wasn't worth it.

Selling a 400B Block (+.030 Over bore, magnufluxed), 383 Forged Crankshaft, Rods, and Pistons. Rocker Assembly and 452 Heads (Magnfluxed and with original valves and springs) Asking $200, located in Newberg OR Not willing to ship at this time.

Looking for an Aftermarket Intake Manifold to finish my budget minded 440 Build. Looking at any of the following, ordered by preference: Edelbrock RPM 7193 Edelbrock 2191 Edelbrock Torker II 5091 Please let me know what you have, located in Newberg Oregon

PM Sent

Sorry not interested in shipping.

For Sale: Dodge 8-1/4 Rear End I removed from my Duster (Upgraded to Dana 60 for Big Block) Unknown Ration based on previous driving should be 3.21. Assumed Open Carrier. 5 x 4-1/2" Bolt Spacing, Wheel Spacers on ends. Can come with the springs if the buyer wishes (Stock A-Body). Looking from...

$100 is fine. I never seen a head crack in a slant, I have seen a block crack from not having Antifreeze (Winter). The owner still drove the car home with the block weeping and parked it. As far as building a more powerful engine, do not invest a lot. After playing with slants for a couple...

Andy, do you have the part number for that Master Cylinder? Did you get the 4 bolt to 2 Bolt adapter from Doctor Diff? Looking at doing that brake upgrade next month if preparation for a BB swap next year!

$650 for a block, rods, and crank in questionable condition. Entire Block needs to be re sleeved due to damage of sitting and already +.040 over

Thanks! Have you seen it? I'm traveling for work for one more week, but would be good with a small deposit.

Thanks! I have tried him/her twice but no response. I will try again today as I didn't realize it was a '72. Thanks!

Hello, Looking for a 340 Block or Short Block in Oregon. This will be for my 72 Duster, not looking for numbers matching or anything. Planning on a small rebuild. Have had bad luck with Craigslist in this area (Driving to Seattle and ending up with a cracked block). Willing to pay for what...

can I jump in line next?

What about converting to the 8in Power Booster and using a 383 B Block? Is there enough clearance to lash valves or remove valve covers with stock style? What about the after market style? Next week I will give Wilwood a call about their master cylinder and just going manual. Thanks!

Planning a major drive train conversion on my 318 '72 Duster after the New Year. I have settled on the 383 for the conversion, but also have a 440 as well. Currently both are cores that need rebuilt, and I have 440 Source Heads that have already been checked out. Looking at using Schumacher...

Planning a major drive-train swap after the new year in my 318 '72 Duster. The goals are aligned with a used Mustang/Challenger/ Ect. 400 crank HP, basic EFI (Holley Sniper/ Fitech), Overdrive, basic suspension/brake upgrades. The Car is currently an Automatic, and the plan was to stick with...

Yeah, I was taught to have the center of the pumpkin offset. The U-Joint works best when it has a little bit of angle. This is counter intuitive to what you would normally think. Are you tied to the QA1 Rear End? For the money, I would invest in the RMS Street Lynx. Either of these kits will...

No way... not even close. I built something similar in my Yellow Duster without using Clifford items. I would say it was between 200-225 hp. Milled the head, Megasquirt TBI, cast iron exhaust manifold, Erson 270 cam, 3.73 Gears, home port job. Best time was high 15's, driver skill could be...

I would not recommend the FAST EFI. I have installed the FiTEch with good luck, but would lean towards the Holley Sniper just for the customer support aspect. The big win of the Fitech is the fuel command center. It is a simple solution for a simple problem that trips up a lot of people...

Next in line, shipping to 97132

Ask yourself... Do you love the car and want to keep it? I love my Duster and have had opportunities for other cars, but I want my car and am willing to sink money into it. Either way this is a hobby and you are going to dunk $10k than $20k than... I'm digging it, and I think for $12k you...