Search results for query: *

  1. mopardemon340

    pin terminals for steering column

    anyone have a part number for the male pins used in the steering column connector. rewiring my car and want to replace the pins to keep splices down to a minimum.
  2. mopardemon340

    Headliner help

    out headliner came with the vinyl already installed..kind of worried that if i trim it. it will cause the headliner to start failing and.plus th vinyl is rapped over the edge if the plastic
  3. mopardemon340

    Headliner help

    Replaces the cardboard and vinyl
  4. mopardemon340

    Headliner help

    72 demon. And not taking the back glass out
  5. mopardemon340

    Headliner help

    Has anyone installed a classic industries abs vinyl headliner in there car. Do I need to put my windshield back in before pulling the gasket back over the headliner? Then did you also have to trim the headliner to fit correctly in the front corners so the gasket lays flat and not rippled. 72 demon
  6. mopardemon340

    Windshield installation

    Should I be using an adhesive when installing my windshield? or just rely on the rubber to leak and hold glass into car if in an accident?
  7. mopardemon340

    Dash pad texture

    I had my dash repaired and they cant get the texture proper. What is everyone using to retexture your dash pads.
  8. mopardemon340

    Relay wiring

    Wire diagram for autec8 1 touch wiper activation kit. Dual Speed Wiper Control Module « autoloc.com
  9. mopardemon340

    Relay wiring

    My wire diagram. the green represents the low speed wiper the purple represents the high speed wiper the orange represents the park for the wiper. the green and purple function as normal with the relays. to make the park function work like it should once the wipers are turned off i had to change...
  10. mopardemon340

    Relay wiring

    I think I got it figured out. I'll test tomorrow and see how it gos
  11. mopardemon340

    Relay wiring

    Anyone good with wiring relays. I got a spdt relay I want to wire up. I know how to wire it but want to see if can wire it differently. I know current flows from terminal 30 to 87. But I want to wire it so current flows from 87 to 30. That way I can wire 30 to the one point with 2 different...
  12. mopardemon340

    Wiper wiring

    The autec8 is the module that will control the wiper motor with a momentary push button switch. Press the button for 1 sec is low. Press again 1 sec is off. For high is the same steps but you hold it for 3 sec. The hard part will be to wire the led in the switch to light up while in use. So...
  13. mopardemon340

    Wiper wiring

    Actually I did and I got ot figured out. L, H ,p1 p2 all figure out. Thank you
  14. mopardemon340

    Wiper wiring

    What I'm doing is replacing my old wiper motor with a new one. But I'm also going to be using an autec8 wiper module to allow me to use both speeds of the motor with a non locking push button. To wire the autec8 up I just need to know what the 4 pins are on the motor. Since my wipe wiring has...
  15. mopardemon340

    Wiper wiring

    I'm replacing my wiper switch with a push button switch. I know that will only give me one speed but that's fine with me. I dont drive the car in the rain as it is but still want a wiper just in case. So heres my what I need help with. It's a 2 speed motor and need help with what spade is for...
  16. mopardemon340

    42/46RH pressure switch piping dilemma

    Please make a schematic. i would like to do this and I'm really confused on how to wire it even more so when you add relays and switches.
  17. mopardemon340

    wiring headlight help

    Yea im going to add fuses to keep everything protected.
  18. mopardemon340

    wiring headlight help

    Thays what I was thinking and y it wouldn't be an issue cause there is no load in the switch cause all the major load gos to the relays.
  19. mopardemon340

    wiring headlight help

    Well i figure with my H and L beam already on relays all i would need is one more relay to handle the rest of the lights. The switch can handle up to 5 amps but recommend to not go over 3 amps with out relays. my LED lights only draw 1.3 amps. So i figure if i wire a relay i shouldn't have an...
  20. mopardemon340

    wiring headlight help

    im redoing my dash and getting rid of the stock switch and making it a push button. would there be an issue with running my instrument lights, marker lights, and head lights off one switch with relays? basically i want to push one button and it turns on all my lights. headlight already has...
  21. mopardemon340

    Trunk floor pan

    I take it you dont know how to weld? if you do its really not hard all you doing is making spotwelds. Be sure to jump around so not to heat the metal up. Also usr smaller wite like .020 or .025 smaller wire will help .
  22. mopardemon340

    Qft carburetor help

    never had this issue until I went from my Holley street avenger 770 to a qft ss-850. Nothing was changed since the engine was on the dyno except for the carb. Transfer slot properly by an engine builder. Timing 18 btdc Idle 950 Intake lift .353 degree at .050° 235°/288° Exhaust lift .353...
  23. mopardemon340

    Qft carburetor help

    Never had these problems until I went to a mechanical secondary. The vacuum secondary was flawless and set on the dino. Only thing that's changed was the carb. Went from a holley 770street advantage to a qft ss-850 Transfer slot is set. 950 for idle, 10:1 compression, intake lift. 353...
  24. mopardemon340

    Qft carburetor help

    I'm pulling between 12 and 13 for vacuum in park. But I pull 10 while in gear. So i guess i need to drop to 4.5 PV since its recommended to check it while in gear with an automatic. Just watched a Holley video that said check in gear
  25. mopardemon340

    Qft carburetor help

    The hesitation happens both when you get on it from a stop and when you take it easy from a stop. It's just not as had when when you take it easy. If I shift the car manually it doesn't have the hesitation.
  26. mopardemon340

    Qft carburetor help

    Thanks for explaining it to me. That helps alot. I'll let you know tomorrow what happened with a standard acceleration. Right now I'm positive it happens only when you get on it from the stop. And with slow acceleration it doesn't do it. But I'll verify it tomorrow.
  27. mopardemon340

    Qft carburetor help

    It has a hesitation off the line from a stop then gos. It's not a big hesitation but its enough to notice it. I seen the graphs but it just confuses me cause I dont understand how to read it.
  28. mopardemon340

    Qft carburetor help

    6.5 is what came in it and still the proper one for me.
  29. mopardemon340

    Qft carburetor help

    I idle at 950 and slightly lower in gear. 408stroker, edelbrock rpm air gap intake, 904 trans, 3.73 rear. What else would you like to know. How do I know if I'm getting my shot to soon or to late for my engine
  30. mopardemon340

    Qft carburetor help

    Got an Qft ss-850 crab with mechanical secondary. The carb works great except for a slight hesitation off the line. Change the squirter size up 2 size but still have the issue. When I move the throttle the pump arm moves instantly and I get a shot of fuel right away. I'm running a pink...
Back
Top