Search results for query: *

K frame has been modified. $50 plus shipping from 95008.

LCA’s with sway bar tabs. $100 plus shipping from 95008

Mallory Unilite distributor for small block mopar. Adjustable. Currently set up for 16° advance. Works perfect. $75 plus shipping from Campbell, CA 95008

Pair of lower control arms with sway bar tabs and K frame. K frame has been modified. Please see pictures. Asking $250 plus shipping. Parts are located in Campbell, CA. 95008

I want to install a cast iron manifold with big ports on to a 1984 318 with small ports. Should I use the small port gaskets or big port gaskets? And what’s the best gasket to use? The 318 is all stock. Thanks FABO.

New $250 shipped (lower 48) Located in 95008. Small dent at the bottom of the coil. Jeg’s Part Number: 555-40500K1

In one valve cover, I've got my PCV valve connected to vacuum on the back, at the base of my carburetor. But for the opposite valve cover, what would be better, a breather or connect to the air cleaner? Thanks!!!

Looking for Mopar Performance black valve covers for a Magnum engine. Thanks!!!

2176. All holes look good. No pitting. $200 plus shipping.

Set of MP valve covers for LA small block. $100 plus shipping or trade for magnum MP valve covers.

I’ve got a LD4B that came off of a 318. I was going to use it but decided to go with a Magnum engine. All the bolt holes look good. It has some pitting in the thermostat housing and a repair on the bottom. $250 plus shipping. Thanks!!!

Hey FABO, I have 4 wheels that came off of my ‘71 Dart. They are 5 on 4 sbp and 14x4 1/2. Local pick only. Thanks!!!

I've got a good running, all stock, 5.9 in a 1996 Ram 2500 and want to swap it into my '71 Dart with an A833. I have some questions about my parts list. I will be purchasing a flywheel from American Powertrain FWCH-10004CS. Is this the best route to take in order to keep the FI? Should I be...

I want to look for a 5.9 and use my A833, but all I can find is engines attached to automatics. Do I need to look for a 5.9 mated to a manual transmission, for a drilled crank? Do the automatics have a drilled crank to accept my 4 speed input shaft? I’m not to concerned with the correct bore...

I started out trying to get .050 off of my reverse switch, because the lights would not come on. I had a friend turn it down and when he was almost done I heard “Oh ****”!!!!... He stripped the threads!!! Now the replacement switch takes a 15/16” (old 7/8”) socket but it won’t fit because of...

It’s that time of year, for me. Pull the mini bike out and get it ready for use. It’s easy this year, all I have to do is tighten and lube the chain. I always drain the carburetor before I park it, so no maintenance needed there.....I got the rolling chasis off of Craigslist and the engine...

Do I have the wrong pivot? I bought the 12.5” fork but it keeps getting pushed in further than the contact on the throughout bearing. So I pulled the pivot, and I think it’s wrong. Overall, It’s about 1 1/4” long. I think it should be about 1 7/8” long. Can anyone verify I have the wrong...

A little help needed, please. I found a 340 about 100 miles away from me. The owner inherited it and doesn't know much about it. I've been trying to find information on it but nothing comes up....This is all she gave me -- HM340R 36930152. Thank you!!!

Do I really need the reverse detent ball and spring on my A833?

After opening my transmission, I discovered that it was missing 16 rollers that belong in the main drive pinion. The snap ring was there but no bearings. I plan on putting them in, but is it typical to leave out these bearings?

I'm looking for a mechanic to go through a Craigslist A833. Tag says it was born 11/1966. It spins freely but I noticed the front bearing retainer had cracks at the bolt holes. Thanks FABO!!

Hello all, I just picked up my new project. A 1971 Dart, automatic with a 318. I am going to keep it stock, for now...but I am no stranger to automotive forums, after a while I'm going to want to do some "improvements"!!!! Thanks for having me!!!