Search results for query: *

  1. Tims 66 Cuda

    Return Line Routing

    The sending unit on my 66 Barracuda tank has two out lets. A3/8 for fuel to the pump and 5/16 for a return I guess. Is the 5/16 for a return or not, as I,m trying to install one to avoid a vapor lock/ fuel boil issue. Any help appreciated. Tim
  2. Tims 66 Cuda

    Speedometer Cables

    Hi all, I need a speedo cable for my 66 Barracuda. The correct length is 59" i believe. I can find a 61" will this work. I can also find a 59" but its for a Camero / Firebird. I wonder if this will cross over. Any help appreciated. Tim
  3. Tims 66 Cuda

    Street Demon Insulator

    Does anyone know of an insulator gasket thats compatible with a Street Demon 625 carburetor. Thanks in advance. Tim
  4. Tims 66 Cuda

    [WANTED] Bucket Seat Molding Clips

    I,m looking for the molding clips for 66-67 bucket seat lower trim
  5. Tims 66 Cuda

    66 Barracuda Quarter Window Adjustment

    Ive got my glass all in and lined up well. Every time I role the quarter glass up , Its low in the front about 3/8 of an inch. I can set it into place by hand and everything lines up well. Roll it up again and the same thing. Is there an adjustment Im missing. Any help welcome. Tim
  6. Tims 66 Cuda

    66 Barracuda door glass stop

    Its been a few years and I cant remember if the door glass stop had piece of rubber gasket on it. If anyone can help with pics or knowledge Id appreciate it. Thanks, Tim
  7. Tims 66 Cuda

    66 Cuda Door Glass Bushings

    Does any one have a pic of the front door glass bushing that the pin on the regulator arm goes through? I bought a kit for this , but I dont think it has the right part. Any help appreciated. Thanks, Tim
  8. Tims 66 Cuda

    Starting issue

    Im trying to start a newly rebuilt 360. Timing and everything is spot on. The engine is 10-1 compression, Comp Cam XE274H, .040 over. When I set the choke and pump the throttle, it hits once and then nothing like its starving for fuel. Any help appreciated. Thanks,Tim
  9. Tims 66 Cuda

    Vent and A Pillar Gasket

    Does any one have pics of the gasket that goes between the vent frame and the a pillar. I cant remember how the gasket attaches. I know it goes along the screws in the vent frame. Any help appreciated. My car is a 66 Barracuda. Thanks,Tim
  10. Tims 66 Cuda

    Car Starts in Gear

    I have a 66 Barracuda Im finishing up. I,ve installed a B&M shifter. My question is the car will turn over in any gear. Reverse light are working when in reverse position. Is It adjustment or bad new safety switch. Any help appreciated as electrical work is my weakness. Thanks,Tim
  11. Tims 66 Cuda

    66 Barracuda Fender Turn Signals

    Did the sharks tooth turn signals have a gasket between the housing and the fender. If so does any one reman them. Thanks, Tim
  12. Tims 66 Cuda

    Engine Turns Over With Key Off

    I,m having trouble finding out why the starter turns with the switch off when I connect the battery switch I,ve checked the starter wires an grounded the NSS. I,m at a loss. Any help appreciated Thanks, Tim
  13. Tims 66 Cuda

    Aftermarket Gauge Wiring Help

    Ok, dont beat me up to badly. Electrical is my weaker point. My question is what is the best way to wire power to the gauges so they operate when the key is on. Is there a post(accesory) for this? also for lighting , what is the best source for this? Ive got the sending units and grounds ok...
  14. Tims 66 Cuda

    [WANTED] 66 Barracuda dash bezel

    Looking for a dash bezel for my 66 to restore. Any help appreciated. Thanks, Tim
  15. Tims 66 Cuda

    Fuel Vent Question

    Does the fuel vent line actually go into the fuel tank or not. Looked at lots of diagrams and cant say for certain. I,m installing the fuel filler neck on my 66 Barracuda and I know it clips into the chrome sleeve an goes thru the floor pan. Any help appreciated. Thanks, Tim
  16. Tims 66 Cuda

    Oil Sending Unit Wiring

    I,m installing the instrument cluster in dash. I want to use the dash gauges. I,m also installing Auto Meter oil and temp gauges. My question is can I tie into the Auto Meter sending unit for the original oil gauge or put in a separate sender for the dash gauge, or forget the dash gauge all...
  17. Tims 66 Cuda

    Headliner Insulation For C Pillars

    I couldn't find anything specific so lets ask. On a 66 Barracuda do you install insulation behind the panels on the C pillar. Its been 3 years and I dont remember if it was there or not. Any help appreciated. Thanks, Tim
  18. Tims 66 Cuda

    [Found!] Wiper Switch Bezel Nut and Knob

    Looking for a wiper bezel nut and wiper knob for a 66 Barracuda. I have the plastic bezel just 3+ years later I cant find the rest. Thanks, Tim
  19. Tims 66 Cuda

    NSS Wiring Help

    First off let me say electrical is my weak point. Ive put a 76 727 trans in my 66. I have the ground that runs from the relay to the NSS. How do I go about wiring up my reverse lights. I also have the original harness that went to console. Any help appreciated. Thanks, Tim
  20. Tims 66 Cuda

    Radiator clearance help

    Im restoring a 66 Barracuda and put a ,73 360 in it. The car had no rad when I bought it. I purchased a Champion rad CC526 to install. I had seen another member use the same one. When I put the rad in, I only have 2.5-3 inches clearance. Im looking at running a solid fan with small spacer. Im...
  21. Tims 66 Cuda

    Header and Power Steering issues

    I,ve installed a 360 with Speedmaster heads in a 66 Barracuda. I,m Installing Dougs D-450 headers. I,m having clearance issues between the headers and P/S box. Is there an after market steering box that may correct this. Any help appreciated. If this may be the wrong forum move it and let me...
  22. Tims 66 Cuda

    Wiper Arm Bushings 66 Barracuda

    Hey all, Ive researched the threads on the subject, but still cant find the answer. The bushings in my wiper arms look to be a press fit brass or bronze. Is this correct and are replacement pieces available? The thin washers and soft washers should be easy to find. Any help appreciated...
  23. Tims 66 Cuda

    Valve Spring Help

    I,m building out a set of bare Speedmaster heads. I have Ferrea Valves with 2.02 intake and 1.62 exhaust @ 5.010 length. I,m running Comp 995-16 springs. Heres the thing, installed height should be 1.700 as per Comp. Mine with micrometer read 1.840. Pressures should be 115# closed and 335#open...
  24. Tims 66 Cuda

    Timing Chain Set

    I bought a Comp Cams kit and the chain set is sloppy as hell. I then ordered a Cloyes set wich I,ve always uesd and it sloppy too. The Comp Cam kit turned out to be a Cloyes set. Does anyone make a tight chain set an more. My go to aint what it used to be. Any help appreciated. Tim
  25. Tims 66 Cuda

    [WANTED] Bearing Hub

    Im looking for a bearing hub for a 68 Barracuda with 10" brakes. Any help appreciated. Tim
  26. Tims 66 Cuda

    [WANTED] Quarter moulding

    Im looking for the quarter panel molding for a 66 Barracuda. One of mine are un-restorable. This is the molding that runs the top of the panel. Thanks, Tim
  27. Tims 66 Cuda

    Door Glass Hardware Help

    I have a 66 Barracuda. Does any one reproduce the correct hardware to install the door glass. I ordered a kit some time back from Classic Industries and it was supposed to be for my car until I discovered some one put a sticker over accept Barracuda. Any help is appreciated. Thanks Tim
  28. Tims 66 Cuda

    [WANTED] Wrist Pin Retainers

    Im looking for a set of wrist pin retainers for Speed Pro H116 CP pistons. Anyone have some or know the part # for them. Any help appreciated. Tim
  29. Tims 66 Cuda

    [WANTED] 360 Block

    I,m looking for a 360 block for a build. My block is past .040 to bore. Crankshaft and rods are good. Any help appreciated. Tim
  30. Tims 66 Cuda

    [Found!] 727 Valve Body

    I am looking for a standard 727 valve body. Its a 1976 transmission. The valve body I have is in rough shape. Tim
Back
Top