Search results for query: *

340 .40 over with less than 1,000 miles on rebuild stock pistons flat tappet cam initial timing at 12 degrees edelbrock avs 800 cfm carb 1964 dodge dart I decided that i would swap out the x heads to eddelbrock 340 heads. Installation went fine but now i have developed an overheating problem...

does anyone happen to have one of these cams? been looking for one and maybe they are no longer made? Thanks

Does anyone happen to have one of these ? Thanks

I was recently talking to someone at a local shop who specializes in muscle cars as they were doing a cars and coffee. They do mostly fords and chevys some mopars. They are also well known in the area for doing great work. I was talking to him about how various things and he brought up how they...

the back of the crank on a pre 68 auto trans to a later small block. I bought some years ago and now I am all out but cant remember where I got them from.

I recently installed a 8 3/4 third member from doctor diff. His 3rd members have the larger u joint yolk. My drive shaft has the smaller yolk. I used the adapter u joint also from dr diff but would really like to change my drive shaft yolk from the small to the large to match the third member...

I know this is a body forum but have a b body question. Have a 383 in a 66 charger I converted to the original air stage one mopar kit, basically the engine compartment stuff. Had the heater box professionally rebuilt. All in the past 5 years. Out of the blue it started blowing warm air. Hooked...

Does anyone know of another source for the sanden sd-5 compressor they sell and include in there kits?- looking to see if there is a less expensive retailer. I want Sanden not a knock off. Thanks

Anyone know if this show is going to happen this year?

anyone have a source for the dark grey color. i would rather spray then but new ones.

Wanting to use this cam in a 340 I am building. Normally I go with the cam manufacture's lifters. However in this case I am seeing folks having issues with Lunati lifters. Hoping to avoid this this problem. What other lifters can I use? any ones that will work with a mopar hydraulic etc.? Thanks

Rebuilding a 340 motor. I am trying to figure out what the cam specs are. The only markings on the cam are J201- on the back of the cam. Does anyone know what this is? cam has a red painted ring at the rear and a white ring around the front I measured the first load came back at .525 lift

Have an issue with my 66 charger 383 4 barrel automatic. Haas a strong fuel smell , not from the carb but from the exhaust when running. My initial timing is set at 20 curved not to exceed 35 degrees. Carb is a newer edelbrock 650 cfm. I am used to the older cars smelling but this one is...

Does anyone know what Trick flow has to offer over Edelbrock. i have used Edelbrock in the past, just curious now that we have Trick flow as an option.

Hey everyone, I have a peculiar issue I was wondering if anyone has a solution I have a 408 4 speed . I had an edelbrock 750 on it then switched to a 750 dp. The DP is about 2 years old. The DP is much stronger from a dead stop. Accelerated hard . But when I have it floored out it seems to...

I tried a 650 dp on my 408 after having a edlebrock 750 that i really did not like. What a difference it pulled much stronger. Then I put a 750 dp on because it makes sense that the 750 would be better than the 650 given the cubes. Nope the 650 absolutely out pulled the 750 dp. Both carbs are...

Came off a 65 273 motor. In good working order. I replaced the 273 with a 318 and no longer need the manifold. Asking 200

Have a nos speedometer for either a 65 barracuda or Valiant. Has a slight bend at the top. Comes in the original box. asking 250

I have a super rare formula s tach for sale. I have not personally tested it ( my dad did), but have had this tach since the atleast 1991. I forgot about it and recently found it. Needs to be cleaned up but otherwise is in great shape I just added a photo after i cleaned it up. The paint on the...

Just swapped in a good running 340 with a 4speed into a 65 dart. Initally had trouble because when the clutch pedal was pressed made a really loud sound . Changed the clutch , it was used anyways ( I was trying to be cheap) and now when i pressed the pedal in without the motor runnig I hear a...

65 dart just did a swap from 318 to 340. Manual transmission. Has a loud weird noise and the engine slowed down like the clutch was grabbing when i depress the clutch pedal. So I take out the trans to see whats up and i have 5-6 small ball bearings on the groundThe clutch absolutly grabbed as i...

Hi everyone, Put a od in a 64 dart has a 318 . The threaded cluch fork adjuster is in a funny angle. Not alighned with the clutch fork. i posted another question on here earlier but now have it all back in the car . I installed the od about 10 years ago and the z bar lenghened to make the...

Just removed from a 64 dart. No issues no noise. Has 9 inch brakes and 2.93 non posi gears Asking $20 Comes will all brake hardware minus the parking brake cables

SOLD I have a set of early a spitfire headers. I really do not want to ship them but i can if needed. I live in the San Fran Bay Area asking 300, they have never been used

I have an issue with my 65 dart 318 4 speed. i put in a overdrive transmission about 10 years ago and had to modify the z bar by making it longer so the clutch fork and the z bar would meet up. The issue I was having was the clutch fork does not sit centered in the overdrive bell housing opening...

Trying to get some information for my father. He has a 73 Dart sport with a 7 1/4 with BBP . He is thinking he can use the 7 1/4 BBP backing plates on the 8 3/4. His goal is to retain the wider brakes and the bog bolt pattern. My goal is to avoid him getting started on something that will not...

Looking for an air gap for small block. -thanks

Just checking how strong the market is for a 1956 Desotos. My uncle has a number of them. One is unrestored that is in really good shape. He also has at least one convertible. All stored indoors for years. Plus he has lots and lots of parts. They may all be going up for sale soon

Hi Everyone, I am putting an 8 3/4 into my 65 dart that has apparently been narrowed. It did not come with brake lines or the vent and tee. I received custom replacement axles from Dr Diff . I am now working on trying to get the brake line kit that will work for this rear end. However it...

Let me know if you have one. Prefer SBP and has 1 3/4 brakes. I do not need the backing plates or third member. i just need housing and axles. thanks