Search results for query: *

Next in line if Rat Rod Al changes his mind!

Agreed! I have been thinking of going with 1968 LL1 for my car.. was looking for examples when I came across these images.. I dont think its that code but was hoping someone may have the car now and have more info/pics.. I know its a longshot but figured Id ask!

By chance does anyone recognize this 1974 Dart Swinger- image was taken @ Midwest Mopar's in the Park, Farmington, Minnesota May 2015 Was searching google and stumbled across the image, hoping to find owner, I was curious about paint code- wanted to see if there are any other pictures. Thanks...

PM SENT

Sale Pending

Long story short - sale fell through. Adapter is for sale again.Thanks!

PM Sent, Ill take them

Mopar Tuff Wheel Adapter has master spline. Comes with wheel mounting nuts. Was mounted on my 74 Dart.. decided to stick with factory deluxe wheel. $130 shipped Location: Warminster, PA Contact via PM

I tried searching the forums but could not find a definitive answer, I know obviously the tail lights and marker lights vary on a late 60s Dart Swinger but I'm wondering if I can cut a 67 through 69 quarter panel skin and use the lower section to replace that on my 74 swinger... has anyone done...

NEW PRICE- $65 shipped

For sale is a Sunpro Supertach II -White face 3 3/8in It was never installed- some wear from sitting on shelf. The nut which holds bracket to back of tach is included- was removed for pics. $75 shipped Location: Warminster PA 18974 Contact via PM Thanks!

Ill take it, PM Sent

Thanks everyone glad I asked thought they should sit flush...that could have ended very bad! Using Permatex thread sealer, thanks again!!

Thanks!

Getting my Performer intake ready for install on 318... went to install 3/8 pipe plugs but they do not seem to to sit flush using countersunk hex heads, and using 3/8 plug from Home Depot it only seems to go about half way. I don't want to wrench too hard and crack manifold....should the plugs...

Thanks everyone! I Will definitely replace it!

Tear down 318 to replace timing set and found it was replaced appears recently, is this slack ok? Should I bother to replace was going to add tensioner and cloyes 3028 HD timing set.. looks like stock chain style is on there now. Thanks for the help!! .

Do you know what size bore the M/C is? How much? Thanks

If oldkimmer passes, let me know, ill take them.

looking for new or good used white plastic connectors for ignition switch (underdash harness and switch side). Working on 74 Dart Swinger.thanks!

I have add on gauge lights wired to orange, and the radio 12v power/gauge 12v power to the red. Everything works...but seems that if the underdash harness is repositioned I lose power to both the radio and the blower motor. I turned everything on and began tapping on ignition switch connector--...

I just finished installing A new stereo and triple set of gages in my 74 dart swinger. I ran the 12v pos. To the original radio connector, the gauges and radio work however I noticed an intermitent loss of power to the blower motor and radio/gauges... my troubleshooting lead me to check the...

Sent you a PM

Yep that's it now to find one for sale! Thanks!

Thanks! I have been using your HOW TO as my guide... however my kick-down rod is a solid piece..

74 Dart Swinger Not sure this helps at all...green to resistor brown to ground.

Looking for 4 barrel Throttle bracket and the carb section of kickdown linkage Converting 318 from 2bbl to 4bbl holley. Thanks!!

Ill add an inline fuse, its a AutoSound 230, came wired that way. Going to replace fuse in box as well. Thanks

So hooked up stereo and underdash gauges, turn ignition to ON volt meter was reading 12v, stereo wouldnt turn on. Packed it up for night. Went back out today, checked the 1A in line fuse (looks good) checked fuse box all look good. Checked grounds, tight and on clean metal.Turn key back to...

Where is the best place to tap for hot at all times- the fuse box or is there somewhere else better?