Search results for query: *

  1. Quinton Castle

    Found this 8.75 in my buddy's yard

    What do I need to make the swap. I kno I need the green bearings and the axles and newer backing plates. Is that all?
  2. Quinton Castle

    Found this 8.75 in my buddy's yard

    Can you tell from these pictures if its a 62-64 or a 61 and earlier housing?
  3. Quinton Castle

    Found this 8.75 in my buddy's yard

    I'm already running a 7 1/4 with 1 inch adapters SBP to BBP so even if its the same length im happy at this point. Atleast until I'm ready for a mini tub
  4. Quinton Castle

    Found this 8.75 in my buddy's yard

    What length axles did you use i may have a line on a set for a good price? Where did you get the backing plate and the rest of the internal parts from?
  5. Quinton Castle

    Found this 8.75 in my buddy's yard

    Found this 8 3/4 in my buddy's yard under a trailer frame. I'm gonna pick it up from him tomorrow but I have worries. First of all it's a early pre 65 rear and all though it does have 741 chunk in it it has the tapered axles. I have seen guys a guy swap them to the non tapered axles on...
  6. Quinton Castle

    68 complete front suspension + k member on 73 duster?

    So I got a complete front suspension off a 68 for the brakes, BBP, and swaybar. I want to put it on my 73 dart that has drums, SBP, and no swaybar. Got the v8 k member with all of the parts. My 73 is a slant 6 with spool mounts and the 68 with biscuits. Can I use the 68 k member when I do my v8...
  7. Quinton Castle

    Tsp ready to run distributor and E-Core coil install questions

    Oooo ok now I understand thank you for clarifying that for me. Gonna tackle it today and see if she runs. Wish me luck
  8. Quinton Castle

    Tsp ready to run distributor and E-Core coil install questions

    So even tho I have a 5 pin ignition and a 4 pin ballast I sould wire it up as if if were a 4 pin ignition and a 2 pin ballast? I'm confused
  9. Quinton Castle

    Tsp ready to run distributor and E-Core coil install questions

    I am installing a tsp ready to run distributor and e core coil into my 74 scamp and I just want to be sure as to how to jump the ballast resistor. I made a jump wire assuming I needed to connect top post to top post and bottom post to bottom and it would make everything right but I want to be...
  10. Quinton Castle

    My transmission took a dump today

    Here is a better picture of the motor mounts
  11. Quinton Castle

    My transmission took a dump today

    Yea I'm not gonna drive it till I get the kickdown set up correctly should be a easy install on the kickdown rod right
  12. Quinton Castle

    My transmission took a dump today

    FIXED IT!!!!! I had to move that arm it was reading wide open throttle instead so it was essentially waiting till the last possible moment to shift j par thanks for the insight it was exactly as u said
  13. Quinton Castle

    My transmission took a dump today

    This is the problem I'm guessing huh
  14. Quinton Castle

    My transmission took a dump today

    O ok now I understand in other words I need to hook up the kickdown correctly and it should fix the entire issue
  15. Quinton Castle

    My transmission took a dump today

    Is there something wrong with those designs
  16. Quinton Castle

    My transmission took a dump today

    Yes I did. Got it to the proper level and everything
  17. Quinton Castle

    My transmission took a dump today

    U have to jiggle the shifter and eventually if u get it just right it will go into 3rd gear but one u slow down it goes right back to a lower gear. Not sure if its first or second.
  18. Quinton Castle

    My transmission took a dump today

    U have to fight with it quite a bit and wen u get it to 3rd and come to a stop or slow down enough it will drop back to first and u have to start all over again with he fight
  19. Quinton Castle

    My transmission took a dump today

    The rod above is also running between this whick I'm guessing has something to do with the kickdown
  20. Quinton Castle

    My transmission took a dump today

    Ok so looking at the photos its definitely a 904. I haven't looked to see if any of the lines are kinked but I'll look tomorrow. The shift linkage pin (about the size of a finger and travels left to right) had jumped out of the pivot location and I popped it back in. Also a plastic bushing that...
  21. Quinton Castle

    Hot Rod Drag Week 2019

    Did u sign up
  22. Quinton Castle

    My transmission took a dump today

    So my 1975 dart swinger special has been on jack stands for about a month as I have been fighting to find headers that fit (318 w/ ps) idk what transmission is in it but I think it's a a904 I could be wrong only had the car about 2 months. Anyways I finally got everything buttoned but and...
Back
Top