Search results for query: *

  1. Cudazilla

    A tranny story (t56)

    Thank you!! I’ll give him a shout.
  2. Cudazilla

    A tranny story (t56)

    Right on! After reading your thread,! I think I’m gonna tackle the same thing. I got my tr6060 for $1000 a few years ago so I’m not losing any money going for it. I got the main shaft, input shaft and tail housing ordered. What about that hard to get dog bone? Is there a number for that to...
  3. Cudazilla

    A tranny story (t56)

    Awesome project! Question, did you need the t56 mid plate or could you use the stock tr6060 version? Thanks
  4. Cudazilla

    Tr6060 to 440

    I’m wondering if you ever got any info on this. I’m looking to do the same thing too.
  5. Cudazilla

    Mild 360 Magnum Build

    Me too, I’m curious how well it does, I’m am thinking about the same cam, air gap intake and a thinner head gasket with a stock heads and bottom end. I know it won’t do as well as yours with the eq heads but I’m hoping it will be a huge improvement.
  6. Cudazilla

    Mild 360 Magnum Build

    Just curious, any updates on how the motor performed? I'm planning a simular build as well.
  7. Cudazilla

    How do you prime the oil pump?

    Also, I would pressurize it and turn the motor by hand backwards to get oil in the oil pump gears so they are primed. I'm sure it's fine, just my OCD. You did get oil in the bearings so it's good on lube on that side of the oil pump. Good job!
  8. Cudazilla

    How do you prime the oil pump?

    Technically you can pressurize the oil system that way, but I would suggest you go through the port on the oil filter housing so that the oil travels through the oil filter before it hits your bearings. I know it can be a pain to access but if you can't get to, I would make damn sure everything...
  9. Cudazilla

    How do you prime the oil pump?

    Yes, it will lubricate the oil passages in the engine for pre start up. The oil pump is a gear pump so if you rotate the crank the opposite direction, you then will force oil back through the pump down the pickup tube and into the pan and therefore priming the pump. Hope that helps.
  10. Cudazilla

    2010 5.7 Hemi into 1971 Demon

    No problem, good luck!
  11. Cudazilla

    2010 5.7 Hemi into 1971 Demon

    Well I corrected myself, here is a add for stock oem non msd lifters with years and applications, if that helps
  12. Cudazilla

    2010 5.7 Hemi into 1971 Demon

    I believe if you go with the 6.4 cam, you also need different springs and pushrods due to the lift. Also I would go with hellcat lifters as they are pretty beefy compared to stock older versions. Maybe someone can correct me if I'm wrong but I read somewhere that dodge used msd lifters in older...
  13. Cudazilla

    Hemi Swap 2014 5.7 VVT

    The differences from a truck to car are the intake, the ram uses a dual runner intake with a SRV valve that switches at upper rpm range. The front cover/and Accesory placement, and a slightly different camshaft. So, if you run a 6.1 intake that will eliminate that problem, I would go non MDS...
  14. Cudazilla

    How do you prime the oil pump?

    Installed it to the oil filter housing plug.
  15. Cudazilla

    How do you prime the oil pump?

    I have a mityvac brake pressure bleeder. I just used one of the male quick disconnect fittings from one of the master cap adaptors(which is 1/4"npt) and bush it to 3/8" npt. Pressure it up to 15lbs and rotate the crank by hand to lubricate the cam and main bearings. If that helps.
  16. Cudazilla

    [SOLD] 2014 5.7 hemi engine 8,000 miles

    It will take Schumacher motor mount adaptors to the v8 k member.
  17. Cudazilla

    [SOLD] 2014 5.7 hemi engine 8,000 miles

    2014 dodge challenger r/t 5.7 hemi engine with 8,000 original miles. Engine ran before it was pulled and turns over freely. Has been stored in my shop since the day I purchased it. It comes with a harness that has been cut by the pcm, and an engine cover I mint condition. Perfect for a...
  18. Cudazilla

    [SOLD] 2014 5.7 hemi engine 8,000 miles

    I just lowered the price to $2,600 if anyone is interested, nice motor!
  19. Cudazilla

    [SOLD] 2014 5.7 hemi engine 8,000 miles

    I just lowered the price to $2,600 if anyone is interested, nice motor!
  20. Cudazilla

    Landed me a ‘64 barracuda!

    I used to have a 74 roadrunner, I think it looks great!
  21. Cudazilla

    Landed me a ‘64 barracuda!

    Awesome!!
  22. Cudazilla

    [SOLD] 2014 5.7 hemi engine 8,000 miles

    Here is a 2014 5.7hemi engine from a dodge challenger r/t with 8,000 miles on it. Practicaly new! I purchased this motor in 2015 for my 70 cuda project. It has been stored in my shop ever since. I recently acquired a 6.4 hemi so I'm changing direction with my build and no longer need this...
Back
Top