Search results for query: *

If possible I would make a fitting to screw in the head bolt hole and attach an air line. If you have access to a welder or can drill out a 7/16? Bolt with a way to mate an air line you could do a leak down test or at least listen to the air escaping. Just a thought.

Question. Do those ARP head bolts use washers too? If so I used them too and it is recommended that you place lubricant on top of the washer for an accurate torque reading. Not under the washer but where the bolt rests on top of the washer.

Thinking out loud here. The crack goes from the water jacket to the bolt hole. Not the cylinder. At least from the picture. How is coolant getting into the crankcase or cylinder? It would have to travel from a poor head gasket seal. Looking at the gasket, are there signs of this leakage into...

That is disappointing. I’m curious. Not saying this was the cause but did you retorque the heads? It’s a step many people opt out of because it means removing components and down time. It is a very important step. Deciding to use replacement head bolts is another thing to think about because...

Your biggest issue will be a correct four barrel and jetting to work with the 318. It doesn’t have the valves, ports, exhaust and cubic inches like the 340. My best carb with a 318 was a 273 four barrel. Not sure about the bolt pattern though for that manifold. Maybe a 273 carb can use an...

These are trimmed wheelhouses from Arizona to ease the work load for someone. The top portion is not trimmed because these are installed differently depending on the user. ORIGINAL FIT - ORIGINAL GAUGE METAL $250 obo plus the ride Packed and ready to ship or local pick up. Location 13618 NY...

I haven’t assembled a small block in years but do the intake bolts on the ends next to the water crossing pass into the valley to perhaps allow water to mix with oil? You put sealer on the intake threads? This of course happens do to a gasket not sealing. Throwing it out there… Sounds like...

For what it’s worth the thread was good to see because now I know about the bolt issue.

Purchased last year these fenders are new. The project car had a change in status. I will ship or pickup directly. I can use Fastenal for shipping for reasonable rates. Location NY State 13618 $550 each or best offer.

A few thoughts to add Just to rule out any head or head gasket issues you might want to perform a compression test. Do you have oil and water mixed in the radiator? If it was a junkyard motor were the heads surfaced? Maybe the intake side was not milled as well and it’s not sitting...

Got it thank you

I appreciate the help! Thank you

Thank you. Nothing on the fenders - right?

I am doing metal work on fenders for a 1970 Swinger project and have other model car fenders on the car that I have to convert. What emblems/holes (if any) do I need for the Swinger Fenders? Is there just rear quarter emblems? I know there are emblems on the trunk lid as well. it would be...

I have these five center caps that I believe were on a 1972 Scamp. They are not what I need but came with my car. They are at different levels of quality but good quality for at least for a daily driver. Small bolt pattern. All of the chrome is in pretty good shape. $75 obo for all five plus...

These are trimmed wheelhouses from Arizona to ease the work load for someone. The top portion is not trimmed because these are installed differently depending on the user. ORIGINAL FIT - ORIGINAL GAUGE METAL Reproductions in my opinion are not the same and are not the same gauge and fit as...

I'm in need of some detail restoration information please. I have a 1970 340 Swinger and I want to begin painting trim brackets and other items as soon as I get them back from glass beading. The car has a black interior bucket seat - console setup. It's a numbers car and I'd like to get is as...

I’ve been away from home lately. Thanks for all the replies. I’ll check out your pictures. Thanks again for the help.

Thanks I will check my inbox

This is a great start. Does the power steering bracket bolt to engine casting? The bolts leading to the timing chain cover? I see the front two piece bracket for the power steering utilizes the timing chain cover bolts through water pump? The AC compressor bracket bolts using the top timing...

Thank you Any chance you could take a photo showing where the bracket mounts? Can you do another picture inside showing the vents? It's kinda fuzzy? If you have a photo of the power steering area that would help as well. Thank you!

I received my 1970 340 Swinger that was a factory AC car in pieces with parts in boxes and crates. The car is being restored at home and I am trying to prepare the parts I need for future assembly. I have looked at the service manual and it wasn't much help. I've been looking for pulley and...

These are trimmed wheelhouses from Arizona to ease the work load for someone. The top portion is not trimmed because these are installed differently depending on the user. ORIGINAL FIT - ORIGINAL GAUGE METAL Reproductions in my opinion are not the same and are not the same gauge and fit as...

That's good news. Glad it worked out. Having fixed "mistakes" in the metal shop I know just about anything can be repaired. Example they sleeve cylinders. I could see how a rare damper such as six pack external balance damper could be repaired. It's just metal. Bore it. Sleeve and weld into...

A lot of discussion. I can add as a retired machinist and having built many Mopar’s of my own : All dampers started with larger bore stepped to a smaller interference fit to finish off. I never had to measure the bore but I can tell you even a same size bore is difficult to install. I would...

I have had trouble locating someone who reproduces the 70 Dart trunk gutters. Does anyone happen to know of a source? AMD doesn't make them. I have seen someone list trunk gutters as the same 70-76 but AMD doesn't list them as the same. Thank you

These are trimmed wheelhouses from Arizona to ease the work load for someone. The top portion is not trimmed because these are installed differently depending on the user. ORIGINAL FIT - ORIGINAL GAUGE METAL $250 obo plus the ride

These are trimmed wheelhouses from Arizona to ease the work load for someone. The top portion is not trimmed because these are installed differently depending on the user. ORIGINAL FIT - ORIGINAL GAUGE METAL $250 obo plus the ride

I have these five center caps that I believe were on a 1972 Scamp. They are not what I need but came with my car. They are at different levels of quality but decent enough for at least for a daily driver. Small bolt pattern. All of the chrome is in pretty good shape. $75 obo for all five plus...

Yeah that’s a trans dip stick. I’m looking for an oil dip stick but I know people have interest in those too. Thanks