Search results for query: *

Putting together a 1969 383 and was about to do the timing chain when I noticed the crank timing gear slides right onto the crank. No tapping required. Should it be tighter fit? I know the damper will probably tighten it up but still thought it would need a hammer to put it in place.

looking for .528 cam seems like there no making them anymore

building my first motor a 383 and came into a dilemma. its a budget build and don't know what rods to get. the two ones i was looking at were the 440 source factory replacement and the eagle H beam. what like some opinions on it!

I found a 1969 727 core that I was gonna pick up for my 383 build. is it worth it to build them or should I wait and find a 1971 and up to build? I do plan on abusing the dart.

I just ordered to steely 15X7 with 4”bs for the rear of my 1970 dart swinger. It still has the 7.25 rear ended with XHD leafs springs. Will 255/60r15 work without moving the leafs? Or should I play it safe with some 245/60r15s

looking for 2 15X7 with SBP for my 70 dart in the Portland, Oregon area.

I’m just now going into the world of big blocks as I prepare for my first motor build. I have 383 and am on the path right now to figure out what heads to use. I currently have a set of 452 but want to use my vintage DP4B manifold and I know the 452 are for a RB. Now I feel a bit dumb but are...

Looking for a SBP 10 inch front drum hub for my daily driver my RF race spins!

I am planning on putting on some new 10inch drums this week and was going to use a 5/8 whole saw to cut the swedged off to remove the hub but can I then reuse the old studs afterword's or should I replace them?

I completely rebuilding my font end because of a pulling to the right on my 70 dart. Well now it drifts very slightly to the left even after getting an alignment. my Frames teacher at school is thinking it has to do with my -0.35 Thrust angle but he hasn't had time to look at it. could this be...

Looking for a DP4B Intake to put on my 383! If anyone has one they are okay with letting go let me know.

I have been having a problem with my 1970 dart veering to the right after a crash that broke my lower RF ball joint. I clipped a ditch and ripped out lower ball joint and did dent the K frame. I have to this date put on new lower ball joints, tie rods, pitman arm, idler arm. brand new Qa1...

so I rebuilt my front drum brakes on my 70 dart and it makes a clunking sound from the RF and pulls to the right on hard stops. I replaced the wheel cylinders, springs and all the front brake lines but left the shoes because they looked newer and didn't touch the drums either. I have taken the...

$60 free shipping!

Looking for a dp4b for my 383 I'm building trying to keep it all old school

Looking for a set of M/T big block valve covers.

I was wondering what is the easiest way to replace the eccentric bolts for the upper control arm? should I do it with no load or fully loaded or partly loaded? just wanted to get some opinions before start tearing in!

Dose anyone know a part number or name for the hardline that comes of the wheel cylinder on the front drums?

Time to talk about everyone's favorite bureaucracy the DMV! So little while ago I picked up my first Mopar a 1970 Dart swinger in Washington with clean title and was even inspected by state police. I went to get a title at the Oregon DMV and they told me that they cannot register my vehicle...

Looking for a Holly 2280 for my slant 6!

Looking for some super six parts. In need the trans kick down and the throttle linkage. any leads would be much apricated!

Looking for a super six setup ( both manifold's, auto kickdown linkage and throttle linkage) for my 70 dart slant.

I picked up a 1970 dart swinger recently and have stared the processes of getting all the lights working. I noticed while driving at night that the right side of the gauge cluster the temp and fuel side was not lighting up. After contorting my self in ways That my body was never made for I...

looking for a 2dr driving dart survivor to buy in the Pacific North West!

Hey gang! I'm looking for a 2dr 1970 dart swinger in the PNW. would prefer v8 but not too picky. I would like something running or a complete project. Any leads would be greatly appreciated.