Search results for query: *

  1. B

    vacuum and AFR

    thank you that is what I was hoping to hear.
  2. B

    vacuum and AFR

    something doesn't seem right to me. I have a magnum motor, stock compression, Eddie heads, RPM intake, 1.6 rockers, small cam .482/.496 duration 214/220 with a lsa 112. The cam is ground for 1.6 rockers. Timing is at 14 degrees at idle, i am idling around 1000 rpms, carb is a csu (holley based...
  3. B

    Stock Magnum rods/pistons durability ?

    the two that I have never heard anything bad about is Brian at IMM engines and Flying Ryan at FRP. Ryan is more of a tuner but he has shops that he deals with for engine builds.
  4. B

    Stock Magnum rods/pistons durability ?

    The forum monitors must have took it down then I remember a couple of threads on there where PIE was cutting peoples frames to get headers to fit and not boxing it back in. Their tunes were only close enough to get a truck running and then they had to be tuned by someone else. Are you on the...
  5. B

    Stock Magnum rods/pistons durability ?

    if you do not have the PIE top end kit yet, I would recommend you read up on them. Some have had decent luck with them but some have said some very bad things about them. I have never dealt with them but I have heard of them in the Dakota RT community.
  6. B

    Installing a painless wiring system

    i used the painless, the steering column wiring schematic was the hardest part of getting it right. I wound up getting and I didit column during the wiring process and that made it a lot easier... the only reason why I did the I didit column was mine was one of the model cars they used to...
  7. B

    Engine pull question

    I had one like that at one time. I had to trim the bottom of the L portion that bolts to the head off. The parts that stick out was crashing into the fire wall. It also can be a tight fit if you are putting the bolts on the back of the heads.
  8. B

    Mopar Shop SW Michigan

    Agree Rick does good work. He has helped me and many others with their mopars.
  9. B

    [SOLD] MT Small Block Valve Covers

    payment pending on the covers.
  10. B

    Bucket seat covers

    if you check legendarys website, they list the shows that they go to. Sometimes they offer discounts if you order you covers at the show..I think I saved like 25 or 30% off on my seats.
  11. B

    [SOLD] Adjustable Rockers

    sold pending payment
  12. B

    [SOLD] MT Small Block Valve Covers

    moparmike, you are second in line if 44067gtdart turns them down.
  13. B

    [SOLD] Adjustable Rockers

    moparfourever, I cleaned up my inbox and you are third in line
  14. B

    [SOLD] MT Small Block Valve Covers

    I was going to reply in a pm but your inbox is full. It looks like ups is showing 30 dollars. so that plus the 75 dollar for the parts and then 3% pay pal fees. looks like $ 108.15 total
  15. B

    [FOR SALE] SMALL BLOCK HYD ROLLER LIFTER SET

    I bought these and was going to go the route of an LA motor but then came across a magnum motor. I would like to get 250 for them plus pay pal fees and shipping. They will be shipped from 48328. From Hughes website "These are a special set of lifters that we helped to design which DO NOT...
  16. B

    [SOLD] Adjustable Rockers

    I have a set of 273 adjustable rockers for sale. I bought these a couple years ago and decided to go a different route. I would like to get $100 for them plus pay pal fees and shipping. Shipping will be from 48328. -edited to show partial of the shaft.
  17. B

    [SOLD] MT Small Block Valve Covers

    Have a set of MT valve covers that have been sitting in the garage and I am not going to use. I would like to get 75 dollars for them plus pay pal fees and shipping. Shipping is from 48328.
  18. B

    Magnum 360 rebuild help

    With the chineese intakes its a 50 /50 chance you have of getting them to seal. From what I have seen most tend to go with the Eddie on for the magnum carb motors.
  19. B

    Ebay GT45 + 5.9 Magnum + E85 blow thru

    Subcom, are you using timing control on the Fitech or just using it for fuel?
  20. B

    Ebay GT45 + 5.9 Magnum + E85 blow thru

    I was able to find it here at a store called performance tool. I think the socket is a grey pneumatic socket. I was lucky cause they sold me only one socket out of the set.
  21. B

    Ebay GT45 + 5.9 Magnum + E85 blow thru

    I used the 12 points as clearance around some of the springs can be tricky with the 6 points. I was lucky to find a 12 point 9/16" long socket that is necked down to make it easier to fit.
  22. B

    Ebay GT45 + 5.9 Magnum + E85 blow thru

    I have arp studs on my 408 dakota and on my dart. I will have to see if I can dig up the part number I used.
  23. B

    procharger vs paxton

    Come spring time I will be tuning my fitech unit..to messy around here right now. after that is tuned in to where I like it I am adding a supercharger. Engine is a pretty stock Magnum 5.9 with just headers, small cam intake. I was wondering those that have put a procharger or paxton on their...
  24. B

    Ebay Interior

    if you go legendary, go to one of the shows where they are at, normally they will have a show discount of maybe 25% or so.
  25. B

    Magnum swap into 73 Scamp

    if you want to use a mechanical fuel pump, then you can change the timing cover over to a LA style cover and bolt on a cam snout extension like the one Hughes sells. Though this will mean that you will also loose the serpentine set up on the Magnum engine.
  26. B

    Wrong DA?

    for quick stripping of the paint down to bare metal, I used paint stripper, but on a tyvex suit, head sock and googles, then grabbed a wire wheel on my angle grinder to remove the paint stripper from the car. Kind of red neck ways but stripped the panel quick, though if the paint stripper...
  27. B

    76 dodge Dart Wiring Harness

    moparblood, The painless was not too bad actually. I took my time and went slow. I think when all was said and done I had 2 wires flipped around and they were for lights...so really it was nothing bad. I think I had about 20 hours or so into the wiring.
  28. B

    76 dodge Dart Wiring Harness

    when I was looking for a 76 harness, I could not find one anywhere..ended up having to rewire the car with the Painless kit.
  29. B

    LGB trains for around Christmas tree

    LGB trains is top notch, my dad has been collecting them since 1982. If you can find them they have a very nice Christmas train set (difficult to find). The track is great, if it gets dirty you can clean it with a piece of drywall sanding paper, (no need for the expensive track cleaners). If...
Back
Top