Search results for query: *

Side that is missing piece is driver

Early thick casting 360 block with Icon forged stroker kit. 10:1 compression, rings gapped for up to 200 shot of nitrous. Rotating assembly was fully balanced with Fluidamper SFI balancer. Block was line honed and the .030 bore job was done with plates. Zero decked block. Hughes EDM oil through...

With the van lower control arms and an axle flip in rear mine sits 3.5" lower in front and 5.75" lower in rear than my dads Warlock. Still have more ground clearance than my 69 barracuda

$300+Shipping

These are Mopar Performance brand sold by Ritter Racing. New. Have not been installed. These are ductile iron for 360. The 4 bolt centers can be cut down to 2 bolt if you are wanting the ductile without the 4 bolt. $350+shipping

Racer Brown cam I bought for doing a 408 but ended up going to a bigger solid flat tappet last minute. 242/242@ .050, 108 lobe separation angle and .510 lift. $200 +shipping firm. has not been installed

PM sent

Hood is in fantastic shape. No dents or rust. Was originally red but has a semi gloss black over it now. Couple little spots where paint is chipped to see the red on the outside and fade on inside. Ready to sand and paint. Asking $400. would much rather sell local but may be willing to ship for...

Have three for 65 Plymouth Fury. One is in excellent shape. No dents, bends or tears and has original emblem still though it is faded. A good polishing will make it show quality. Second is in nearly excellent shape. Small dent in middle of one of the ribs and is missing the emblem. Third has a...

Edelbrock RPM Airgap dual plane for small block. Has had a gasket match port job to the fel-pro MS90109 Asking $400+shipping. located in Vancouver WA 98682

I have a set and some extra (25) 1.6 ratio rockers with 16 adjuster bolts/nuts. Theses have had some grinding for clearance done but none of which has thinned the sleeve to any point of concern. Asking $225. Located in Vancouver WA 98682 prices don't include shipping

Opps. I realized after posting I was in the wrong section. Anyway to move it the Brakes section?

Sold under Summit brand but is just a reboxed Right Stuff conversion kit. Summit Racing SUM-BK1629 Summit Racing™ Rear Drum-to-Disc Brake Conversion Kits | Summit Racing It is new. Has been installed but decided to go different route before it was ever run or even had fluid put in. It does clear...

Looking for a pair of 15x10 ralley wheels. 5x4.5 big bolt. I'm located in Vancouver WA 98682

Awesome. Thank you!

Still available?

Fastback yes. Realized this morning I probably shouldn't post things dead on my feet and buzzed as this should have been 2 different posts. One in body/trim and one in interiors.

I have a 69 barracuda I'm doing a street/strip set-up but want to keep it original modded looking. It is a y3 yellow 318 4spd with the deluxe black interior. I'm putting off set springs in to fit some 275/60/15s on my dana 60 that's going behind a 408 (possibly with NO2) so the drivetrain isn't...

Thank you everyone

I have an 80% driver quarter panel for a 69 barracuda. It's new and has a manufacturer sticker in it still but not sure how old it it. Anyone recognize it and able to tell me who made it?

was fully rebuilt last summer with 3.73 gears and a power loc posi unit has maybe 400 miles on it. stock A-body width, 489 case, Richmand gears, crush sleeve eliminator, Green bearings. All parts came from Doctor Diff except the brakes and lines, small bolt 5x4. I have an adjustable pinion...

Thanks for the advice, they are 6 ton stands and so have a wider base, and I do a shake test any time I put weight on jack stands before I completely pull the jack out. I missed that ad for the AMD stuff. Trying to find just partials though.

76 block stock rebuilt cast crank and pistons. 452 heads also rebuilt with polished aluminum valve covers. No cam, push rods or lifters. $3000 can deliver for a fee within reasonable distance of Vancouver WA.

318 was rebuilt bottom to top about 4 years ago but still has very low miles. Drive to work a couple times and to a few cruises a year. Maybe 1500-2000 miles. stock bore and stroke, cast pistons and crank. hand ported 302 swirl port heads running 9.2:1 compression. Billet hydraulic roller cam...

Trying to find some lower patch panels not entire quarters as everything outside the black paint is in great condition. Located in Vancouver WA and would prefer to do a pickup/cash exchange. Willing to drive a bit.