Search results for query: *

Not A body related but I wanted to come and ask here because I have always had good info from yall. Starting a new phase of my project truck got tired of the magnum 318 with a few mods and talked my dad out of his 440. I know the engine came out of a 1973 Winnebago. I will include a couple...

Due to the way my luck is going I need to get my truck back on the road for something to drive while I work on my DD. Been running a 4 speed and then a 3 speed manual behind the 93 Magnum. Due to Bell housing and clutch issues I'm wanting to put the 904 that was behind the la 318 that was in it...

I have two shifters with no linkages on them and don't remember which arms go to what levers. Anyone able to tell or have a diagram as to which one is which?

I need to change yokes and cant remember what size socket I need lol anyone able to help?

I know the 23 spline A833 O/D trans is weaker than the cast 18 spline that is a given but just what will one of these trans handle before they start breaking stuff?

So if you guys were going to build a motor but wanted the most bang for the buck what would you build? It would be going in my 84 D100 Shortbed for street/strip use. I currently have the current engine I have and a few other possibilitys I could go with as well.

I rebuilt my carb yesterday, and when i put the vacuum gauge on it to tune the idle in. I noticed it jumped around quite a bit. I have never had a engine with anything but a factory cam in it so is that normal for a cammed engine or should it stay steady?

I am asking this mostly because I want to learn and progress my ability to properly tune and set up my engines. On my magnum 318 has a pro comp dual plain air gap intake, flowtech headers, and a 4160 vaccum seccondary 600 CFM holley. It has always been a little slugish from idle if I just...

Everyone if you like Science fiction books please check out my friends new book. I actually really liked it and I am trying to help him get the word out about the book. Check out the website and if it looks like something you would like hit the link on there to amazon and get it and leave a...

Working on my truck again but I know you guys will know and help me. I had I leaky wheel seal on one side it didnt leak bad but it leaked. Now that I have changed rear gears both sides are rivers of gear lube. What do I have to do to change them? Both bearings are in pretty good shape...

I know there is dozens of threads on here about this but I havn't really found what I am looking for. I am considering putting a set of LA heads on my magnum because I would like to get rid of the problematic cracking issues of the magnum heads. I do not know if mine are I have not had the...

Does anyone have a fuel sending unit for a 84 pickup?

I'm bored and starting to plan for a future engine build. Thought I would come here and see what you guys thought would be the best choice. My choices are the classic 451, 470, 500, and a 512.

I am looking for some type of software where I can design and build cars to come up with ideas for future projects and pass time lol. Any suggestions?

I am still parting out my 73 dart sport still have fenders, doors, all the glass, good grill. Trunk quarters are good. Anything else just ask and I will see if I have it. Have 8.25 axle unknown ratio until I pull it. All the discbrake parts minus the caliper brackets.

I have the trim for sale on ebay at the following link. If a member is interested I can pull the ebay listing and work a private deal. Mopar 70 76 Duster Demon Windshield Front Window Trim Molding Set Used Dodge | eBay

How do I properly set my pinion angle? i am doing a axle over swap on my truck and want to make sure I get the spring perches welded on correctly so I dont have any issues.

I know we have a huge sticky but that says its for 67-72 cars mine is a 64. What all parts do I need from my donor vehicle which is a 73 dart sport. What should I buy new while doing this swap? I already plan on new lines/hoses and master cylinder and more than likely calipers. As always...

I got a set of plugs for my 98 Durango 318 and a set for my 93 truck 318. I wasn't really paying attention to the fact the plugs were actually different I put the rc12yc's in the Durango. Will having the shorter nosed plug in the newer motor hurt ? I don't have emmisions where I live.

I just want to make sure of everything before I mess anything else up. Due to my inexperience I messed up my 489 case gear set. If I am going to have to pull it apart anyway I might as well swap to gear I want instead of the 3.23 open that's in it. Will my other 741 case work in my...

I had broke my yoke on my 489 I got one today and the old one slid right off new one slid on i put a new ujoint in it and took it down the road. Now I have a whine when deceling in gear. Do I need a new crush sleeve and if so how do I change it?

I was wanting to see what y'alls experiences was with going from a gear like a 3.23 to a 4.10. My truck has a magnum 318 with a cam and a 600 holley and a OD 4speed. It actually gets good MPG idk exactly what its getting but it will go alot farther than my durango does on the same amount of...

I know this is a stupid question but I honestly don't know and I want to do it the right way. How do I set the timing on my 318 with a bigger cam? Its a 318 Magnum with a 600 Holley and a drop in ready to run distributor. The distributor advance should be 24º CENTRIFUGAL AND 10-14º VAC, Cam...

I need the yoke for a 8.75 rear end 10 spline let me know what you got.

I have a 1973 dodge dart sport I am parting out. The front seats, sunroof, hood, vinyl top trim, and rear sail panels are gone. I still have all the body parts in good shape rear fold down seat car. If you need anything let me know and I will get you pictures and we can make a deal.

I need to temporarily bypass the rear brakes which way will work? Leave the line unhook with no fluid in the master ( i'm almost positive this wont work but want to make sure) or plug the rear line?

I picked up a Mallory 685 for next to nothing yesterday, didn't come with instructions. Can anyone tell me how to wire this thing up? Also will it work with my pro comp distributor or will I have to put a stock or different aftermarket distributor in?

Tonight is the first time I have gotten to drive my truck. I noticed it has a very bad dead spot where it just flat falls on its face no power horrible sounding. Below that spot sounds good runs fine above it inst terrible but doesn't pull like I think it should. Here is what I have its a 93...

I have all the Z bar, rods, and brackets for my truck now but I need the little bushings that go in the ends on the ball studs. Dealer quoted me something like 22 bucks a half so it would be $88 to do the job. Will these work...

I got my 318 Magnum fired up the other day getting close to having it driveable, its a stock magnum other than a dual plane intake, 1" spacer, and a small cam. 107 LSA, 206/212 @ .050", 258/264 adv, .512"/.522' lift. Its in a truck but it wont be used for truck purposes other than maybe...