Search results for query: *

NEED complete front clip from the firewall forward. Going into a 73 Challenger that was in an accident in the front end. I am in Canada close to Niagara Falls N.Y. 14303. Please PM me if you have or know where I can get this. Thanks Onig

Just finished building the MS3 V3.0 with the Xpansion board. I have my JimStim hooked up and am trying to get the RPM gauge in TunerStudio to work. I have followed the instruction on the DIYAutotune website for the Gen 3 Hemi...

Hi, I just finished building my MS3X. I want to test to make sure all is working good. I have the Jimstim built as well. I am learning to use the TunerStudio. I finally got the MS3 to communicate to my laptop. A base tune for a 6.1 would be good to have so I can test and get to learn the...

I am guessing that all the Gen 3 Hemi injectors can interchange physically. I am also under the impression that they are High Z injectors. So does anybody know if bigger injectors from other vehicles will fit in the new Hemi? Looking for injectors from 60 to 100 lbs/hr. I tried searching the...

On the Gen III Hemis, who's injectors are used? I am trying to get parts together and sometimes come across injectors and if any of them match I can scoop them up. Do any other engines use the same injectors as the Gen III. Manufacturer? Part #? Thanks Onig

Can anyone supply injector part numbers for the Gen III hemis. Did a search but could not find anything. Thanks Onig

So the new 2014 Ram trucks of 2500 and 3500 will have the option of a 6.4L Hemi. Does anybody know anything about these heads, good, bad, in terms of performance. Any changes made to them? Does anybody have a part # for these heads. I called a few dealers near me and they want the VIN, which I...

Help to decode this 833 for me please. 3324866 PP8332789 0150 Thanks onig

I found a vehicle with a dana in the scrap yard. I have the crossreference parts list that I found under the seat. The dana # 603835-3 or -4 I could not find this BOM in my parts list nor on the Spicer website. Anybody can figure it out???? If it is a 60 I will be pulling it. Thanks onig

Has anyone used the 440 Source flywheel that they sell. It comes with a removable weight for internally balanced engines, or you keep the weight on for external balance engine. http://store.440source.com/1045-Billet-Steel-Flywheel-New/productinfo/113-1014/ They said that it will work on SB as...

91 LA block 360 with factory roller hydraulic cam. Now with a comps cam, hydraulic roller as well. What should end play be and how to control it. I checked by hand and it probably has about 0.150". I have not seen a spec for it. When I go to the shop I can easily check with dial indicator if...

I am trying to removing the pipe plugs for the oil galleries but need the tool for it. It is 5/16" square. I had made one from 5/16" keystock with a nut welded to it a long time ago. I went to use today and it is F*_Ked up, so I want to buy the proper tool. SO who sells this 5/16" square tool...

I have a bare D60 housing that I will be narrowing as soon as my wheels and axle ends come in. What I need to know is "how can I accurately measure pinion center-line"? Where do I measure to and from, remember this is a bare housing that used to be full floating. Pics would help as well if...

Has anyone converted the side gears in the Trac-lok of the Dana 60 to 35 spline side gears? I have a Dana 60 out of a truck, 4.10, with trac-lok that has 30 spline side gears. I think some one mentioned that Ford D60 use a lot of 35 spline axles. The BOM number is non existent. I called a local...

Anybody else have problems with MT tires. We had MT Sportsman, could not get them to seal properly to the wheel, kept on leaking past the bead and rim. The run-out of the tire was horrible. Sent them back received a new set, one sealed but the other did not. We put tubes in them to make them...

I have a stock big block electronic distributor. I want to change the advance springs. I have only seen two springs in a package. Is there a bunch of different springs to choose from or is it just the two in the package that are available. I want to recurve my dist real soon. You guys that have...

Need 71 Valiant dash cluster wiring diagram for non rallye dash. I need to know what the circuits are for the round connector that plugs into the printed circuit board. Thanks gt

Looking for an A body 8 3/4 rear end housing or complete unit. I don't need backing plates or brakes. I currently have a B body rear in my 69 Dart but really need a shorter rear housing. So an A body or narrowed rear housing may work for me. Toronto, Ontario PM if you have anything at...

How do I remove the headrest from my 69 Dart bench seats? gt

Does anybody run the following MT Street Radial sizes on 10" wide wheels? 295/65R15 #3762R 275/60R15 #3754Rhttp://www.mickeythompsontires.com/strip.php?item=ETStreetRadial What I need to know is the section width (widest part of the tire). I know that MT states that the widest rim is...