Search results for query: *

Looking for big ball joint boots. Anyone know where to get them? Which are the uppers/lowers.

Looking for some advice on shifters. I have 560HP 68 Dart. Using the stock shifter and looking to upgrade. What do like & why.

Ok I'm having starting issues. I only have 8.5 volts at the coil. Not enough to start the car. If I run a jumper from a good 12 volt source to the coil car starts with no problem. Details include the following; MSD coil, MSD ready to run distributor. No MSD box. Any ideas on where to start?

Looking for 68 & up LH a-pillar trim piece. color doesn't matter. No breaks or cracks. Shipping to 55369

I'm looking for some advice on installing a GTS tail panel on a 270 decklid. Does anyone have a template? Lots of holes to drill and want to do it right from start.

Looking to get a driveshaft made up for my 68 Dart. low deck, 727, 8.75 489case, with 1350 yoke. how do I measure it to assure a correct length? Or does anyone have the measurements? Thanks.

I'm looking for advice from you Dart owners. I've mini-tubbed and moved the leafs in board. I don't think I can run the exhaust in the stock location. Looking for pictures or suggestions. Thanks in advance.

Good Sunday to you all! I'm looking for pictures of how you routed your plug wires. I'm struggling to make them look good. Any pictures of BB routing is appreciated. Thanks.

Looking for a 383 date coded engine block - late 1962 (Oct-Dec).

I have a heavy duty trans cooler for sale. Brand new never installed. Comes with relays all wiring, fittings, sending unit, and instructions. I went a little overboard, so my loss is your gain. Located in Osseo, MN. 55369 Paid over $240. I'd like to get $175 and I'll take care of the shipping.

I'm looking for recommendations on trans coolers. Specs are 500ci LD stroker 560hp/590#. 727 Torqeflight. 4000 stall converter, 3:91s.

Can a guy use 70-72 Dart doors on a 1968 Dart?

I'm a little confused when it comes to wiring diagrams. Looking the diagram in my service manual, I see ignition 1 and ignition 2. Am I wrong in assuming they (1 and 2) are for Start and Run. If so, which is which?

Looking for a rust free, STRAIGHT passenger side door for a 68 Dart. Glass or no glass. Must be straight and rust free. Thanks.

Can I use this crank on a 3 speed wiper motor? If not, where can I get a 3 speed arm?

Ok fellow Mopar lovers, I'm looking for pictures of your aftermarket trans cooler installs. My high stall converter is going to generate some heat, so I purchased an auxiliary cooler with fans. Looking for creative install locations.

I'm looking for a centerlink. 73-75 a-body in good shape, not bent etc....Thanks

Ok this subject has been beaten to death but I'm still confused. (go figure) I have a 68 Dart converted /6 to BB (Low Deck) I'm using the /6 k-member and am running into issues with idler arm header interference. I purchased "BB" pitman and idler arm. After looking at Rock Auto they have the...

Need header bolts for my new TTI's. Any suggestions.

Ok guys and gals let see your creativity when it comes to junction/relay boxes. I've seen people run the + cable to the engine compartment into a junction box and run relay from there. Lets see some pics. Thanks.

I'm converting to a 3spd wiper motor on my 6 pack Dart. Looking for advise as the 2spd and 3 spd are wired differently.

67-69 A or B body steering wheel. Driver quality or better. With or without horn ring.

Ok, this has probably been covered a million times but here goes... I have a 1968 Dart thats mini tubbed and the springs have been moved in. The axel housing is narrowed as well. My ? is how much wheel and tire can I fit under my Dart?

I'm looking for pictures of aftermarket 6 pack set ups. I'm at the point where I need to put together my fuel lines. Specifically from the mechanical pump to the carbs. I working with a low deck 400. Thanks.

Anyone using Cool Carbs plates and gaskets. Looking for results and opinions. Thanks.

I'm looking for recommendations on getting my GTS tail panel restored. It's in good condition just needs a little work.

I'm going to replace the harness's in my 68 Dart. I'm not an expert with electrical so I need recommendations on easiest install of new wiring harnesses. Thanks in advance. Details.. 1968 Dart 500ci stroker, MSD 6AL, MSD Billet Distributor, Electric cooling fans, Trunk mounted battery.

I have for sale a pair of bucket seats. They were pulled from a 1967 Barracuda. Tracks are in great shape. No rust and they work flawlessly. I have two sets of seat backs, both are in good shape. I'm looking for $450 plus the ride. I'm located in Minnesota.

Fellow A-Body members I need help. My computer took a crap on me and I lost all my reference pictures. I'm looking for those of you that have installed frame connectors and how you ran your fuel lines. For reference I'm working on a 68 Dart. Anybody have any Pictures?

Looking for some help in finding the write up in Mopar Muscle about a budget build low deck stroker. I believe it was in an issue published in the last 18 months. Thanks!