Search results for query: *

Ive got a waterpump that sends the lower to the right side, Ive got that figured out, My upper is an issue, was running a universal flex hose but its starting to kink, I tried a 55091 upper that is universal and has a 90 degree at the T stat neck but its too long and I dont want to trim it down...

Looking for a complete third member (391 posi) in good working order, must be able to ship or be in or near Ct, Thanks

Schumacher adapter motor mounts for a slant 6 k frame to go up to a b / Rb engine 130.00 Schumacher Mopar Motor Mount Engine Swap Kit 1967 to 72 225 S6 to B/RB Swap | eBay

Im building a 440 dart, I first had a 68 TRW pump from my slant 6 but my pulley would not line up, found out rb pumps have a longer snout, I then purchased a new Saginaw pump and mount but I cant get the high pressure line to fit between the biscuit mount(r/b k frame) and I cant find a good...

I got my hands on the steering coupler updated rubber cover instead of the metal cover with the tabs you pean over, my header tubes are 1/4" away if I run this without the hose clamp, I didn't know if they were a silicon type , I'll need to update with a photo shortly

I swapped a factory big block Kframe in to my 68 Dart For some reason the left side seems lower by about 1" , the pitman Appears to be up all the way, I swapped both the idler and pitman with another Set with the same results, I didn't know if it was normal to be lower on one side

Having trouble with the routing on the new right stuff lines, can't figure out in the engine bay do the route between the block and the oil filter or between the block and motor mounts? Thanks

I'm reassembling the front suspension witha disk brake setup that was included with the car off another A body, everything looks fine to me but the number 2627 on the spindle shows as B body, don't want issues later

This K frame was suppose to be a big block K frame ( It came with the car and I was told it was a direct connection) I just installed it in my 68 Dart, a 6 cyl conversion -I looked at a lot of online photos and I could not find a similar one , Notice there is a factory looking notch on the...

Have basically 2 short blocks good for a basic refreshing , on is a 68 318 and other is a 77 360 I have a set of heads and a 4 barrel aluminum intake, make an offer for both blocks, need the room, located in ct

I have the complete 225 "charger" labeled on air cleaner-engine and transmission still in the 68 dart, runs and drives great, removing soon for a big block swap- 18k original miles, make a reasonable offer- Located in ct

Looking for both rear shock plates fir an 8 3/4 or dana 60

I have a aftermarket partial quarter panel. Has a square lower rear marker light which could be welded for a 67-69 or use for a 70 +. I went with a full quarter. Located in Guilford ct. Local pick up 100.00

Time to start my next project, 68 dart - body is done and the AMD fenders fit nice, Ive got a DC BB kframe and a 440 to build, Ive been collecting parts for a while, Im going to start swapping out the rear and work my way forward. Im going to order the 6 leaf 383 springs and Im tempted to go...

Ive got a 72 Dodge dart. Solid floors and undercarriage, Small hole in trunk floor size of half dollar, 318 4v motor, runs strong, PS,PB, Dual exhaust, Black interior, bench seat needs recovering, Car was originally Yellow, Right quarter needs new panel, Will consider partial trades on parts for...

I have fender well headers from Hooker, could use a sandblasting and fresh paint, would consider trading towards non fenderwell A body headers 250.00 located in CT,

Ive got a 68 v8 convertible needing a full restoration,was in storage for 15 years, Complete, power top works,Motor turns over , auto,split bench. needs frame repair front left near the tork box , quarters, I want to build a 67-71 A or B body hardtop that I can build a big block car with, must...

I have to many projects so so this one must go, Its pretty close . See my link to the ebay auction for description and photo's, It located in C t. http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=320594757461&viewitem=&sspagename=STRK%3AMESELX%3AIT

I have a 68 dart ragtop and I have a OEM not repop hood in good overall condition, Not perfect but decent. What are they going for? I see reproductions in the 550 range

Looking for a 10.5" bell housing to fit my 68 dart - Going to a big block. Also looking for headers and other big block swap stuff- Thanks

Im having trouble locating a prebent front right steel brake line. Anyone who sells the kit only sells the entire kit which I dont need, I could make them but I would like a nice steel prebent line? Anythoughts? Thanks

Can anyone recommend a supplie for a complete brake line kit for my 68 Rag top dart? Thanks in advance

I was wondering if anyone has drilled and re studded the front A body sbp drums to Lbp Thanks

im looking for front fenders for my 68 dart. Also looking for 8 3/4 L.B.P axles ready to go in a dart and drums 10"-Thanks

Just looking to see if there are any swap meets coming up this spring - Thanks

I have 10" rear drums and 9" front on my 68 Dart convertible I need to replace the non-power master cylinder and I was wondering if I should just get the 1968 replacement or is there a better year that will bolt up and perform better. Thanks

I need rear shackle mounts and fendersl for a 68 Rag top dart