Search results for query: *

  • Users: dustoff440
  • Content: Threads
  • Order by date
  1. dustoff440

    crossover tubes

    I need a reliable source for a bolt in source for the crossover tubes on my kelsey hayes front disc brakes, 70 Dart any help would be greatly appreciated
  2. dustoff440

    [WANTED] kelsey hayes brake parts wanted

    getting close on my Dart I need the bolt and nut that holds the brake pedal pushrod to the brake pedal arm and also need the brake push rod (kelsey hayes 4 piston set up) I seem to have misplaced this hardware
  3. dustoff440

    ralleye wheel question

    I have the 5x4 ralleyes (small bolt pattern) on my 70 Dart. They are only 5.5 inches across. Did they make 5x4 ralleyes that were 7 inches wide like the 5x4 1/2 ones?
  4. dustoff440

    wilwood adjustable proportioning valve

    has anyone used one of these any input would be appreciated Wilwood 260-11179 Proportioning Valve : Amazon.com : Automotive
  5. dustoff440

    correct painting for 70 Dart grille???

    I would really appreciate if someone could post a pic of the correct paint scheme of a 70 Dart grill.
  6. dustoff440

    Best fitting dash cover for 70 dart ?????

    Looking to spend around 100-125 bucks
  7. dustoff440

    msd 8680 adjustable timing

    anyone using on of these, would appreciate some feedback http://www.summitracing.com/parts/msd-8680/overview/
  8. dustoff440

    alternator excitor wire from ign switch...

    can i wire it to either wire on the voltage regulator and...is it wired on the start circuit or is it wired from the ON position, I have a wiring diagram but I can't read it cause I cant find my friggin glasses LOL
  9. dustoff440

    msd coil wires too short...

    where I want to mount my msd6al in the engine compartment , the wires to the coil are about a foot too short. Is there any reason I cant add an extra foot of wire to make it reach??? would it change the ohms or resistance or anything like that???
  10. dustoff440

    avoiding using relays??

    Im totally rewiring my car doing my own thing. To avoid relays I am running much larger gauge wire and than necessary and just using an inline fuse for each component. Is there a problem with this??
  11. dustoff440

    using old carpet for insulation???

    Being the cheap *** that I am, Im thinking on using my old carpet under the new one for insulation I was planning on trimming back all the points where the carpet meets the edges and using the old carpet as sound and heat insulation has anyone done this?????
  12. dustoff440

    [WANTED] Kelsey Hayes 4 piston disc brakes hoses (NEW)

    Got a 70 Dart with the KH factory 4 piston setup. I need the hoses for both sides (new please) NOT the feed hose from the master cylinder but the hoses/lines that feed from one side of the caliper to the other I would be willing to buy them from a member or if someone can tell me where I can...
  13. dustoff440

    Front end alignment specs?????

    I am almost ready to take my dart in for a front alignment It is a 70 with the factory big sway bar. Kelsey Hayes brakes and And bfgoodrich ta radials factory slant 6 torsion bars and KGB gasadjust shocks. I have no idea what numbers to give the alignment guy The car will be mostly street...
  14. dustoff440

    cammed up slant

    Slant 6 hyper pak - YouTube
  15. dustoff440

    LA valve covers on a Magnum

    I tried a set of cheapie chrome covers on my stock magnum with a crosswind intake and there was interference where the covers are recessed to clear the runners.....is it that they are cheap or has anyone else run into this Im not really interested in buying a good set and having to...
  16. dustoff440

    ADVICE:Baseline carb jetting/engine timing/spark plugs

    Almost ready to fire up my 360 MAG since rebuild Need advice on starting points for jetting / timing/plugs Heres the specs: 92 360 Magnum bone stock block/ rods/pistons/ crank/ std bore stock heads crosswind air gap intake mopar performance distributor msd6al/blaster coil out of the box Holley...
  17. dustoff440

    Converting an automatic steering column to manual

    Is it possible to convert a 70 Dart column automatic to a manual column by just swapping the parts off a manual column??? I have the stock column went to a B and M floor shifter and want to lose the column shifter. I have seen where guys would grind the column shift boss off and fill it in...
  18. dustoff440

    reasonably priced cowl/hood weatherstrip????

    I can't seem to find reasonably priced trunk and cowl weatherstrips, come on 45 bucks for the hood piece is frickin highway robbery!!!! Help to find decently priced would be appreciated.
  19. dustoff440

    Vintage Barracuda Club Owners Welcome Packet

    Don't really want to sell it but I would if someone just had to have it. pm me with an offer there is a decal and patch for more and better pics send email
  20. dustoff440

    [FOR SALE] shock extensions bolts

    $12 shipped
  21. dustoff440

    [FOR SALE] 67-70 Dart master cyl drum brakes

    NEW, Bendix 11323 67-70 Dart 4 wheel drum drum brakes $40 shipped
  22. dustoff440

    [FOR SALE] 70 Dart wiper harness

    $21 shipped, I rebuilt this for use on my Dart but went a different direction.
  23. dustoff440

    [FOR SALE] 40 chrome air cleaner lids

    I have no idea of application they are about 10 in in diameter 20 plus actual ship cost from 34731
  24. dustoff440

    [FOR SALE] handful of /6 rocker arms

    $20 shipped
  25. dustoff440

    [FOR SALE] 2 or 4 outlet fuel blocks

    $16 each shipped 1/2 inlet 3/8 outlets
  26. dustoff440

    [FOR SALE] shock extensions bolts

    $16 shipped
  27. dustoff440

    alternator id help please...

    was told this is a 100 amp police alternator????
  28. dustoff440

    [FOR SALE] early 90's honda trx 90 4 wheeler

    plastic body not so great mechanically excellent within the past year: new carB new tires(2) new stator $350 obviously local pick up only central fl 34731
  29. dustoff440

    low pressure fuel injector??????

    Is there such a thing as a low pressure fuel injector that would work for example at 10 psi? I want to install fuel injectors in my sidepipes to add to the size of the flames coming out, and dont want to have to bear the expense of a high pressure fuel pump/fittings/hardware etc.
Back
Top