Search results for query: *

Two locking pliers were required, it seems Chrysler put thread sealer which makes sense to keep moisture/water out, over 50 years it solidified and become more of an adhesive, making a straight forward fix not so much.

:BangHead:Anyone else have problems unscrewing the socket from the back of the housing on a 68 marker light, I tried liquid wrench, pliers, locking pliers, any insight here is much appreciated, just need to replace the bulb and don't want to damage this light assembly, if the part was an old...

Hi CudaJunction, I tried to unscrew the socket off the housing and it won't move, unless it's a reverse thread I'm going to apply a bit of liquid wrench and try again, I wouldn't mind if the light was decrepit but its a NOS piece.

Hi, I need to replace the bulb in the round marker light on my fender, I took the assembly out, is the socket on the back of the housing the same set up as the tail lights? where it pulls out and pushes back in, its giving resistance at the moment and I don't want to break it. Is the replacement...

My factory dash lights are bright with higher RPMs ( example car on choke or car moving), but become very dim when the car is stopped, yet the 6 Autometer gauges always have the same consistent brightness if the car is stopped, moving or not even running. What's up with that?

Clockable

On my 68 Cuda tried a MP mini starter and still had clearance issues due to the headers even with the heat shield off, ended up buying a clockable starter and problem was solved.

Maybe a clockable starter will fix your problem, it fixed my problem when there was no way to get the MP mini starter to fit in my car. Check out robbmc starter website www.robbmcperformance.com , only problem is most clockable starters cost huge.

Hi, can someone please verify if these are the correct headlight adjusters for a 68 Barracuda.

As far as it doesn't matter what is attached to the car as long as it is properly aimed how about these bulbs. You think you can aim these properly and still be safe for others on the road? Not using HID headlamps on my car and have no intentions on doing so, I'm happy with my halogen seal...

I don't care what people run for headlights on their cars, then can duck tape flash lights on the front of the car for all I care, just as long as the beams have been set up properly, so I'm not being blinded by the beam directly in my face.

Running pertronix with the flame thrower coil on my 68 Cuda 340, happy with it, had no problems.

Thanks 67dart273 for your help, my tail lights are working fine, so I will direct a family member to check the inst. fuse.

Thanks, I will take you advise, I have become completely useless to do anything until my problems can be corrected.

Hi, my factory gauge lights including my 4 Auto Meter gauge lights stopped working all at the same time last night, but the actual gauges all still work as they should and every other light on the entire car works perfectly fine. Is it safe to say this is a blown fuse, sorry I have a hernia on...

Update: Thank you everyone for the replys, I'm happy to announce it turned out to be the flasher switch and I actually found a spare one in the tool box which I wasn't aware of, it has made in U.S.A stamped in big bold letters on it which is always a bonus these days, gotta love when things work...

4spdragtop good question, I was always under the impression that there was one flasher switch for the turn signals and a seperate one for the 4 way flashers. I did hold the turn signal flasher in my hand a few minutes ago and it did make a clicking noise when the right signal light was on, but...

Hi, just need some insight please, to avoid fixing things that are not broken and buying parts that are not required. My 4way flashers work perfectly all the way around including the hood mounted lights, when the turn signal indicator is activated, all right side lights work no problem, when the...

Crossfire use to make it, not sure if they do anymore, I don't have a part number, I should have bought two of them at the time.

Hi pishta, that is the cap I'm talking about, all the crossovers are done underneath the cap so the wires on top can all be installed side by side.

I just installed a new Crossfire distributor cap on my 340 that I purchased many years ago, is anyone else running this cap on their small block, if yes did you have any problems with it or did it work fine? I don't think this cap is even available anymore, tried searching for it on the...

Thanks Dan, will definitely try your suggestions.

Hi, some insight please, the headlight switch shown below with the male tab on the end indicated by the red arrow, is this for a ground wire to be inserted. I checked the headlight switch in my 68 Barracuda today and could not feel this thing present when putting my hand up behind the dash. I...

If your working with 7inch round headlights, I have a pair of half moon chrome covers in mint condition available.

Hi wazoo64, yes I have the RobbMc starter on my 68 Barracuda 340. I tried the Mopar Performance mini starter, as compact as it may be, it still would not clear the header pipe(I have hooker headers on the car not T.T.I). I felt beating the tar out of my header was not an option. Where the...

I've done exactly what Dan is mentioning, eliminated the M.P. ECU and the ballast resistor on my 68 Barracuda 340 and installed an AC Delco D1906. No need to carry spare ECU'S and ballast resistor's in the glove box anymore.

Thanks Redfish, that's great, all I need to know.

Sorry my car is not with me right at the moment, just need to verify, the bulbs inside the marker lights on a 68 Barracuda are they just standard peanut bulbs similiar to ones used in the dash.

Hi N.B.D. the alternator came with a wire to ground it, the instructions show one of the field terminals needs to be grounded with this alternator.

Hi Mr.Hemi, I was looking at those Blue Mopar Performance voltage regulators. They all are listed for Race only, not sure if that would be compatible on a street car.