Search results for query: *

I have 2 right now.

I think so, no one has told me of a setup that it hasn't worked on yet. I have 2 right now if you would like one. Sorry I missed your post for so long. Steve

I have 2 right now. Paypal $110 to [email protected] with your address if you still want one. Thanks, Steve

Yes! I have some ready to ship right now. I'll PM you.

I have a 3/4" bore wilwood master cylinder. My pedal is the 5 1/4" pin to pin. I should probably put together my entire parts list and post it here, once I get some time this winter.

I did not change the location of the rod mount. Drilled the dowel out and put a bolt in. I also have a TR6060 with stock clutch and throwout bearing. I had to put a T ontop of the master to get it to get air out so I could bleed it.

I do. I just don't have any of the backing plates right now. Send me a DM please. Thanks, Steve

Finally got the Barracuda on the road to today to grab a couple gears! The pedal feel is better than my '09 Challenger.

When you get a master cylinder the instructions will tell you which port is which. I have a Wilwood, and it's the same as the Yellow car. I had trouble getting my stock Dodge master cylinder for TR6060 bled out, and I put a T with a cap on so I could bleed the line to the slave cylinder as the...

Shipped the trans to Texas Drivetrain Performance. Disassembly showed 3rd and 4th gears got hot, indicating a lack of fluid in the trans at some point before I bought it. Not sure how it was low, there is no drain plug in them. So, paid $2k for trans, bellhousing, flywheel and clutch. Gonna...

I've watched videos on how to check alignment, but, I believe the inside of the housing needs to be round? How would you measure this?

Got the trans out, input shaft bearing is shot as the input shaft wobbles around. I'm not sure why it went bad.

Yea, oil in the gearbox. It has some metal flake in it. Trying to get motivated to pull it out, I'll check to see if trans is centered. Thanks

Pulled the starter out, everything looks like it is working correctly. Link to the noise, it happens in 1st and reverse just above idle. Does not happen in neutral. Definitely think its something in the drivetrain. It was a used trans, so who knows if something is wrong with it or something I...

No plate, just the dust shield (14 ga?) between the block and bellhousing. A quick search on some parts diagrams doesn't show a plate. I have a passenger side starter, TTI headers that specifies that I use the following starter for clearance: MUST USE A Chrysler mini starter part no...

Hello, Take my 67 Cuda with 5.7 and a TR6060 up and down my driveway, makes an odd sound. I think that the starter is still engaged. It's not cranking, but i think the gear is still engage to the flywheel. I don't know as there is any alignment or spacers that go in. I just bolted the starter...

Finally got to see how the clutch release is! It feels good, hopefully I'll get more practice this summer!

Yes, I still have some available. PM me please. Thanks, Steve

I still have some available. Paypal $100 to me and I will get one shipped out to you. Thanks, Steve

I do, I'll DM you. Thanks, Steve

Thanks for adding all that desmo900. I have more produced and ready to ship. I believe I have contacted everyone that was on the waiting list, If I missed anyone, I apologize. I had more produced than were on my list so I have more to sell than the preorders. Let me know. $100 each Thanks...

You are on the list. Thanks

UPDATE: I have contacted the machinist, will be ready to produce more within a couple months. I have a list of members here that want to buy from this run. I am trying to determine how many I should have made, if you would like to buy, respond here or send a DM please. Price is $100, includes...

Hey @mopardude318 , project is slow. Farming takes up most of my time currently. I haven't had time to change ratio and try the pedal or to get engine running. I'm curious why you used the American Powertrain setup. If you would like to return the parts you bought from me I would refund you...

Now I understand what your talking about, it didn't sink in last winter.

I did not. Look at post # 28 & 29, you can see where I drilled the hole in relation to the spring tab that was cut off. Then following pictures of the linkage and clearance I had with the pedal depressed. I was getting the full stroke of the master cylinder without any interference. My car is...

Thank you Denny! That means a lot coming from someone that sells a reputable product! You found me. The original production run had all of the mounts reserved. I have not heard back from everyone yet, I also have a waiting list if people back out/need to do a second run to meet demand. I will...

mopardude318: your inbox is full, let me know if you still want to buy. Thanks, Steve

Got it! Will be shipped out USPS Monday. Thank you!

Parts are here! Ready to ship out. I had 10 made, I'm using one and the other 9 were spoken for, including Hemidenny and mopardude318 from this thread (I'll PM you). If anyone else wants one let me know and I can sell if someone backs out on what I currently have, or can produce more in the...