Search results for query: *

Im using the same pan. I had to trim my K frame on my 65

What brand are they?

Header selection for an early a sucks. My hookers cook a dual pot master cylinder. Best bet is buy the tubing, bends, and collectors and build your own.

My wife drives mine cuz she is the driver and the seat is bolted to the floor and cage. If I need the car moved its either her or one of the kids moving it.

I searched your old posts, I cant find it.

Will do, thanks

Could someone post a picture of their head liner? I need to install one and was wondering if there are some fiberboard panels on the C pillar.Thanks

Im wanting to put paint on my 65 but my trunk lid is not worth fixing. I found a fiberglass pin one one listed for a 66 dart.

Are trunk lids for a 65 and 66 dart the same? If not what is different?.

Sorry, my work schedule doesn't leave me much time to go online. I would suggest having them upgrade the drive shaft to use 1350 u joints. Just incase you decide later to put in a stroker motor and spray it. Never say never

Yea, ill sell it. I dont know how to ship it though. It has a factory yolk with with 7290 at the prop shaft and if I remember right the rear u joint is a 7290 on the drive shaft and a 1350 for the pinion yolk. Its a combination joint. Its DOM tubing with neapco ends. Made by Ann Arbor driveshaft.

From u joint center to u joint center mine is 50 1/2". The yolk from u joint center to end is 8 3/4". If you are looking for one I might part with mine. I only used it for one season before swapping out to a 904

My engine and trans are from a 1977 M body. Because they never put a 727 in an early a I had to get it made. Also consider there are different length trans yolks. I measure that too.

I have one from my 65 dart made by AnnArbor drive. 318 with a 727 and an 8 3/4 using a 489 case. Would that measurement work for you?

Use the off set upper control bushings to get your caster right.

My 65 dart uses 81 mirada front brakes, spindles, and rotors. I used a 73 duster upper control arms and duster tie rod ends. Also a 73 duster manual disc brake master cylinder.

My 65 has the springs moved into the frame rails using RMS relocating kit and minitubbed to the rails. I run 15x10 rims with 28 12.5 M&H racemasters.

Thanks I needed that.

pretty much did all that. I lopped 100 pounds already. Thanks

Pretty please......... I really want to drop 200 pounds off the car.......any bit helps

Nice, cant have too many early A's

Does look different. If its wide enough I could make it fit. Anybody with a 66 dart, can you measure the inside width of your front bumper from the drivers side to the passenger side.

Im trying to drop some weight on my 65 dart. I'd like to swap to a fiberglass front bumper. I found a company that sells 66 dart front bumpers and I wonder what the difference is between a 65 and 66 dart front bumper?

Thanks

Will a 65 barracuda front clip bolt on to a 65 dart body? If so will the body lines match? I want to drop some weight on my dart by adding fiberglass body panels and no one makes fenders and front valance for early darts. Barracudas I can find. Thanks

Thanks Bad Sport! Got the car out yet?

I want to put the candycane trim back on my 65, most of the clips are wasted. Where can I get replacements?

They got a web site, the owner is a bit........ummmm.....out to lunch....if you get my drift? (Cuckoo cuckoo)

I know you well enough to know that you are a sick, sick man. BTW did you know that Marshall moters in Jackson has two of them pretty cheap.............Yup I'm the kinda guy that would give a fifth to an alcoholic.

Thanks! Now i just gotta find my fender tag. Misplaced it somewhere