Search results for query: *

Sent PM

Sold

Sold

Sold

Price lowered to $200 shipped to the lower 48

It is rated at 800 cfm, if I am not mistaken.

sold

Sold

Adjustable roller tip 1.5 rocker arms with all spacers and bolts. Have been clearance for 0.550 lift (at 1.5) cam on Edelbrock heads. Very good shape, worked perfect when installed. Includes a set of 7.375 tip to tip Ball & cup pushrods, for these rockers with stock hydraulic cam lifters...

Edelbrock Springs 5722 - came off a set of Edelbrock Aluminum heads, never used, minty fresh! $45 shipped to the lower 48 from 36203.

Edelbrock LD4B - in excellent condition, clean, perfect holes. $225 shipped to the lower 48 from 36203

Comp Cams XR286HR-10 - Long nose cam for a factory LA SB roller motor. 236I x 242E @ 0.544I x 0.541 on 1.5 rockers. Installed in factory roller stroker for about 4000 miles, in excellent condition. Does NOT require a brass pump drive! Has cam card, original box, etc. $150 shipped to the...

Comp Cams XR292HR-10 - Long nose cam for a factory LA SB roller motor. 242I x 248E @ 0.549I x 0.544 on 1.5 rockers. Installed in factory roller stroker for about 1000 miles, in excellent condition. Does NOT require a brass pump drive! Has cam card, original box, etc. $150 shipped to the...

I can part this out, but the shipping & Paypal hurts. I can do the cap for $20 shipped.

ThermoQuad 9811S - Electric Choke, rebuilt by David Cheeves (DemonSizzler), never installed on engine, ready to go! Jetted for a warmed over 318, but will handle a stock 340 from 36203. $200 shipped to the lower 48. Electric Choke! Hard to find!

Corrected, thanks!

,SOLD!!! ThermoQuad Brass and Phenolic floats - 2 sets Phenolic, 1 set brass. All in excellent condition, 1 set of hinge pins. $30 shipped to the lower 48 from 36203.

Accumulated ThermoQuad Strip Kit - Primary and Secondary Jets, metering rod assortment, accelerator nozzle assortment, plenty of little spare parts: gaskets, screws, clips, etc. Also includes a secondary butterfly adjustment tool and craftsman screwdriver, organized into a box close to the same...

Carter ThermoQuad Strip Kit 10-203. Complete, except that the secondary Jets 0.139 have been modified to 0.159. Difficult to find set! $65 shipped to the lower 48 from 36203

Wheel Spacers. 5/16" (never used) and 3/16"(barely used). Your choice, $15 shipped, or $25 shipped for both to the lower 48 from 36203.

Part Lot - Most are off a 73-76 A-body. Headlight bezel, door switches, Door Open Handle dishes, 1 stage rear view mirror, map light switch and bulb assembly, etc. All of it for $60 shipped to the lower 48 from 36203.

Used Chrysler replacement roller lifters for an LA Factory Roller Motor. Worked fine when pulled, went with a solid lifter. Rand with the XR286 cam below for about 4000 miles. $45 shipped to lower 48 from 36203

Holley 7455 Economaster 450 cfm Spreadbore carb - Good condition, everything moves freely. $50 shipped to lower 48 from 36203.

Mancini Racing Polyurethane Transmission Mount PTN4422 - Fits: 1969-89 Chrysler, Dodge, Plymouth. Like New - $35 shipped to lower 48 from 36203 From Mancini: Factory rubber transmission mounts were never intended to take much abuse, so the resultant sloppiness in...

Torque Converter plate off of 360, with the 6 crank bolts (no convertor bolts). $20 shipped to lower 48 from 36203

Washer Tank with electric pump, no cracks, motor runs. $55 shipped to lower 48 from 36203

American Powertrain Transmission crossmember for mounting a TKO-600 in an a-body. Like new, never installed. Fix the tunnel to accommodate the transmission, and this replaces the original crossmember. The large ends slip over the rearward end of the Torsion Bar mount, and once bolted in is...

Dana 60/8.75 Trak Loc Sure Grip - 30 spline - 4.10 & down -Pulled from the 3.73 Dana in my Duster after about 5000 miles, replaced with a Detroit Locker for better grip with street slicks. Work perfect, new clutches not required unless you have lots of torque and sticky slicks. $250 shipped...

Price Reduced to $350 plus shipping, no paypal fee.

for a 727 tranny, stalled at 4000 in my 73 408 stroked duster (around 450 hp), yielding 60' times in the 1.65-1.70 range consistently with a 3.73 dana. Drove like a much lower stall convertor around town and on the highway, and got 14 mpg with it! Best 60' times were from hitting throttle from...