Search results for query: *

Nice truck!

I ran those on my mud truck, didn't have to worry about knocking off a valve stem. On another note, went to a tire shop the other day with my daily and the guy didn't put the valve stem cap back on one wheel. OCD kicked in and had to locate one in the garage right away.

Check out summit #29214. Don't know if these could be trimmed to work.

I'm interested in your results and hope you have better luck than me. I ran my Dart at the track a few times with a prepped starting line, and I still had no luck. Yeah it was better than the street but I still got gated by drag radial cars. I just couldn't put the power down. I'm only running...

:popcorn:Interested

Appreciate your input. How long did you run them?

Ok, thanks.

Appreciate it.

I guess I should have worded it better. I meant were the spacers for the 4 1/2" BP only, or more of a universal spacer. Thanks Lee.

The Wilwood spacer sounds like a tight fitting spacer on the studs which would be ideal. How thick are they?

How have they held up? Were the spacers you used bolt pattern specific?

I asking for a coworker who asked me if its ok to run a 1/4" wheel spacer on his front wheel. I have no experience with spacers on the front, and figured someone on here might have. Its on a aftermarket aluminum wheel with taper lug nuts. Its a 73 Dart with disc. The spacers I've seen in the...

I had to do one. Most of the old silicone came out in one long piece. Used a wire brush to clean the area and finished with some lacquer thinner. I used a regular tube of clear silicone in the caulk gun. I put a thin bead on and tried to force it down with my finger first. Then load it up and...

I looked into bolt on wheel spacers recently. Apparently ALOT of Jeep and truck guys run them. I was skeptical due to a bad experience with those cast wheel adapters back in the day, but the ones now are better made. I went to a lot of truck forums and really found no negative feedback. Most all...

Thanks blu, appreciate the info and your time.

Appreciate your input. What's your thoughts of a spacer in the rear, not sure if I'm a fan but don't have any experience with them to judge.

Drag Wheels DR-9 Gloss Black Wheels DR9177054073GB These are the ones I meant to click on 5 x 4 1/2

5x4.5. From what I've read, about a 5.5" BS is good for the front with the big bolt conversion and stock upper arms. I'm looking at a few more wheels. I am curious to know if I'm on the right track with the front BS. I seem to be stuck with running a 1" spacer on the rear to get me to the 4.5 BS...

LMAO, I missed that. Thanks

Drag Wheels DR-9 Gloss Black Wheels DR9177044073GB It says 4 1/2 bolt pattern, which I have. I would have to run a spacer on the back due to stock spring location. Is this BS ok on the front? I know there's some very knowledgeable wheel people on here.

Formula One Super Stocks, my go to tire back in the day. I'd buy them today if I could.

That I know, I'm not sure of all the sizes they come in, the ones I've seen have been pretty short. Not worth tearing up my SG.

Wouldn't want to use on the rear with a sure grip though, correct?

45 is correct with weight of the car on the tire, There shouldn't be an issue shimming it back a bit.

The early centerlines have no wording on them. If I remember right that started sometime in the 80's

I like the Rallys but I understand your ready for a change. I like this wheel, but maybe a side shot of your car would help put it all together. Who makes this wheel?

:(

What wheels are these??

Man those McCrearys were the ticket for a street racer back in the day, before drag radials came about!

I have the Coopers also. A nice alternative to the BFG's