Search results for query: *

oh no question they will mount on the 5.5” wheels but its not ideal, the 5.5” wheels will suck the sidewalls in which will increase the diameter and cause the tire to crown. Also since the tire will be more ballooned or crown more a very low tire pressure will have to be used to maintain a...

I think it blends pretty well, only thing i would maybe do is go with a 255/50R17 in the rear, the 255/50R17 is only roughly 1/4” bigger all the way around but will give you another 1” of tread width. The little bit of added height in the rear will also even out how the wheel well is filled, it...

Are these front tires? Also what size are you running in the rear?

i cant tell you its safe, you have to make that judgement on your own. They will mount on the 5.5” wheels but the sidewall will be sticking out about 2” over the front and back wheel lip. It will put added stress on the sidewall but with them being biased tires they are a little more forgiving...

Its doable but its pushing it, 7” would be ideal, 5.5” will make the tire balloon more, will actually increase the overall diameter.

Most of the aftermarket drums for newer cars and trucks have flat spots milled in the drum in a spot which i assume is to balance, you shouldnt have a issue removing the weights.

I run 28-30 psi in the rears and about 35 in the front, have t/a radials all around. Idk why they get such a bad rap, sure if you try to launch at any rpm higher than 4k you will have a hard time getting them to bite, but they grab decent for street tires. That being said you deff can roast em...

I just run blackwall out, problem solved :lol:

Torque sticks get a bad rep. If the impact is adjusted properly they work great. I agree on hand torquing wheels, i do on both my bronco and demon but at work it takes too much time, unless its a porsche bmw land rover or go fast car they get hand torqed the rest they get the torque sticks

Well here ill make ya lean towards them even more. They have a mail in rebate going on from april 1st until april 30th 2019. $70 rebate if you buy 4 cooper discoverer at/3 4s Cooper Promotions | Cooper Tire

This is true, however most times the cooper isnt much more than the mastercraft, the mastercraft are decent but dont balance as good as the coopers. Wouldnt hurt the op to check on the price though

I have the ridge grapplers on my bronco and love them!

Ok op i put together some options, looks like your ram has 275/60R20’s from the factory. any of these will be a better replacement over the goodyears. None on this list should wear out in 40k miles. All mileage posted are the manufacturers ratings, realistically expect to get 5-10k less miles...

Yeah for sure, huh, dodge may have lowered the recommended on the newer years, i agree that is way too much as well, usually 35 psi is good for a half ton pickup with passenger rated tires.

44 psi? I thought the newer 1500 rams recommended pressure was 40 psi? I know the 2016 ram at work is

What size do you currently have? Is it 4wd? Are you looking for strictly a street tire or a/t?

Still a drag radial is a dot radial regulated tire. The load rating should be similar to the all season in a comparable size.

For what its worth i get good wear running 30 psi with my 275/60R15 bfg’s on the rear

It can be an issue on a car with floating rotors, on the cars where the rotor is the hub it wont

Its also important to remember to go around the lug nuts two or three times to ensure they are all tight, ive tightened lugs up with a torque wrench and the second or third time going around you could see a lug nut or two move slightly and feel it in the torque wrench. Also always tighten in a...

I wouldnt go any less than 80 ft lbs.

That i will agree on

Not enough to make a difference regarding the op. So i guess i googled 26x11.5 slick huh? Well your wrong there again. I spent a good 10-15 minutes on summitracing searching through the 15” tire options with the parameters the op was looking for and posted the results. He was looking for which...

I completely understand that but a tire that is only 1” taller all the way around (2” oveeall) isnt going to make much of a difference. Maybe if you start getting into 2-3” difference towards the ground i could see it. I think i worded it wrong but i meant that a tire in the same brand at the...

Why try to calculate his tire with a fake size when he already said he was running a 28x11.50-15 Same width but lose contact patch? Assuming you were to run the same width wheel a 285/60R15 and a 285/50R15 in the same brand and pressure will have the same contact patch. The only time you will...

You were in the ballpark!

Ok i looked, Continential HSR2 and Michelin XZE2 are the only thing we can even get our hands on at work Just to give you an idea in the 275/80R22.5 these would be retail price per tire including mounting Continential HSR2 $550 each Michelin XZE2 $620 each In the 295/75R22.5 which is a...

Yeah im thinking thats a michelin only size, ill look tomorrow, i have a app for one of our tire distributors and when i type in that size it pulls up 295/75R22.5 Michelin makes a few odd sizes that only michelin makes, ill look for ya when i get to work in the morn Even if ya had to go to the...

Ill look for ya tomorrow at work, if im not mistaken thats a michelin only size, the 295/75R22.5s are the same height

What size specifically? Typical semi tires are 11R22.5 but those are deff shorter and skinnier. They may be like a 255 or something but they are deff low pro 22.5s