Search results for query: *

My preference is for the recovery set-up with a easily visible level and downward tank venting. No fuss, no drips, no hot coolant steam in the face...and I know whats going on without removing the cap, hot or cold.

76-80 F mopar recovery tank.

Unshrouded about an inch is good. Allows for fan flex at rpm and some driveline movement. Shrouded fan doesn't matter how far from the radiator, just blades half in/half out of opening for efficiency.

2-1/4" is pretty thin for a clutch fan blade. I've got one of them thats approx. 2-1/4" but the rest are much closer to 3". The clutch fan blades I've compared are typically a steeper pitch than fixed fan blades.

not a site, measured some from a personal stash. you'll need about 3" radiator to belt/obstruction (other than wp snout) clearance to swing a 2" fan. from your picture it doesnt look like you could swing a big enough blade to do any good.

you can fit 10# in if you stack it carefully. for sure check your pulley diameters. should be a substantial difference, could be an inch or more. checking fan stash only 2 are even close to 2" thick. 18" factory 5 blade flex and a 18" factory 7 blade fixed are both just under 2-1/8". another was...

How thick of fan can you swing in there? Youve got the 1" btwn rad and pump...how much more room behind the pump before you hit belt/pully?

Looks very much like a 77-78 aspen/volare w ac piece. Same offset mtg holes. By 79 they were even. F,M,J and late B bodies have a lot in common.

4 different A firewalls...67-72 and 73-76, ac and non ac. Made a template for my 72 a.c. firewall. Used 080 aluminum sheet. But I covered more than just the fan hole.

how bout a pic or three...with rough dims.... Late B had some similar stuff to F,M and J's.

Nice. CNY was death to a winter driven car of that era. Back when they used salt I remember watching the threshold trim slowly dissolve away... Lucky it didnt get many miles!

20" is 1974-79, A,B,C and E, 318 thru 440 3462190 18" is mid/late 70's up, could be hd cooling on a slant. parted a bunch of those. 3870107 they both have a healthy pitch to them. I'm running the 18" on my Demon. 2 core alum rad, JSD G126, standard pump, no shroud(fitted one but doesnt seem to...

Pentastars and pn's...im sure. There are 2 different factory flex fans, 18 and 20 in. that I'm aware of. Probably more, these are what I've found.

Now you have.

take off the overflow/recovery bottle cap. look at the two hoses coming down from the inside of the cap. The "overflow/puke" hose should be much shorter than the ""recovery" hose. Recovery hose should go to the bottom of the tank. Puke hose should end well above your 1 qt. full line. heres a...

where the lines end underneath the overflow bottle cap/inside the bottle determines which is which.

There is only one line from rad to bottle so the cap either works or doesnt. Cap doesnt control which hose coolant runs thru. Thats controled by where inside the bottle the lines open end is located. Low for dump/pick up, higher for overflow/dumping on ground. I'd swap the two lines on the...

only if theyre viscous zombies:D flex zombies are down another aisle:steering: if you could zoom out in that picture youd see lots of "WTF am I saving this for?" toe stubbing, leg gouging masses of "crap, ive got to move that again"....ugh.:) Lets not even go out behind the shop...no no...:eek:

Excellent. :thumbsup: I've had a couple of those hanging around for years. :D

Factory flex fan Bob or aftermarket?

I've got some 5 and 7 blade viscous fans...bring your own clutch.:D My preference is a factory flex.:thumbsup:

looks like a double a/c hose hole...oval shaped...not factory.

F body bottle

Dayco part number 70975. (pics above) Its listed as "cut to fit", not universal. Just trim ends, as needed. Went thru a sack full of upper and lower hoses to get a good fit.

I agree...the sb has more of a bell shape, bb more square straight shouldered.

now with pictures!:lol::thumbsup:

poster board for templates and aluminum sheet.

hayden plate and fin cooler mounted in front of rad with gap between the two. https://www.amazon.com/gp/product/B000C3F3SO/?tag=joeychgo-20 (mine came with the mounting brackets)