Search results for query: *

1975 PLYMOUTH DUSTER 7 1/4 REAR END 2.76 GEAR IF I REMEMBER RIGHT DRUM TO DRUM $ 25.00 PICK UP IN WESTEN MARYLAND 21783 CHECK OIL DID NOT LOOK BAD AND TOWED THE CAR 3 HOURS TO MY HOME NO NOISE .

MR GASKET VERTIGATE SHIFTER 4 FOUR SPEED A BODY I have a Vertigate shifter that i bought years ago and never used or mounted it it is for A body and has surface rust on the black parts from sitting in my garage for years box rotted away has light scratches on chrome and very small chip in...

HERE are some parts i had removed from a 75 duster . if they don't sell there going to the scrap yard . see if there is some thing you can use. oil pan $ 15.00 plus shipping oil pump pick up $5.00 plus shipping...

I have two New right hand threads tie rod ends with no grease fittings $ 10.00 for both plus $7.50 shipping. I have two right hand thread tie rod ends one is NEW moog ES401r The other one was installed on a car i bought that sat for 10 years when i got it it was not painted so it was...

I Have a Milodon 8 qt street street oil pan with pick up tube #30940. previous owner put a rod through the left rear and patch it . Bought it from him and had to buy a new pick up tube i use this pan for two years with no leaks when i removed it i cleaned it and touched up the out side...

just sold them sorry

I have one rocker shaft right side I think 7 rockers and spacers FOR ALL SMALL BLOCK LA Shaft very little wear same on rockers spaces must be made of soft metal were rusted blasted them still use able only space the rockers . These were sitting in my basement since 1995 would run a brush in...

I have a set of 3/8 stem cut to fit 0.531 outter guide and out side of seal is .620 they are for small block or big block mopar the set is missing one seal you can get one from crane or you can get one from comp cams #505-1 $20.00 free shipping from Maryland 21783

sorry here are pictures

I got a ED Hamburger oil pan and pick up for my engine and it had the Milodon 19050 high volume oil pump kit for small block the direct connection # was p3690852 this is a old nostalgia from back in the day . Took it apart the pump was in good shape body and cover had no wear the rotors had...

thanks

ONLY GOING DOWN FRIDAY TO SHOP FOR PARTS .

Mopar 833 4 speed transmission was rebuild 2 year a go has 200 miles no noise has light pitting on 3 gear from sitting before i got it, no gear noise . some wear on 4 gear synchro teeth but does not pop out of gear is a 1969 a body date code is feb 17/ 1969 fits 67 up 76 a body cars out put is...

Here is the test on walls . if you look it up for a 360 block most sites will say min of 125 thousands , i would not go that low but if you took 0.30 more out of the block it does not need to go that far but would still leave you with over 200 thousands cylinder wall left. The person i got it...

Block has not been filled will post wall thickness on the post.

i can not post the sleeve thickness because i don't know the brand they used , but i can sonic test the thrust side of the cylinders and post it this will give you the total thickness of the cylinder.

NEAR Hagerstown md 21783

LOWED PRICE $175.00

Is 4.060 now you can safely go 4.100 like i said it needs to be bored there is wear were the piston on a stroker makes it turn at the bottom of the cylinder may clean up at 4.070 , will clean up at 4.080 no ridge at top do not know if there is taper . if you look at picture 6 sec cylinder down...

MOPAR 360 non roller block with main caps has been sleeved to 4.060 bore for stroker kit will need to be bored to 4.070 0r bigger if you want. Block was decked just need to clean gasket surface . can be used also as a big bore kit with stock crankshaft and rods ,. . got this in a parts deal and...

Good Used set of Speed Pro l2316-f 30 pistons 10.5 compression .The top were clean with walnut shells and cleaned in parts washer then re coated the skirts with molly coat . The pistons are in good shape the top of the piston have light pit marks from my friend running his engine to lean at...

I have a 1985 360cu block that has been sleeved for a big bore it is 4.060 now will have to be bored to 4.070 or bigger block was decked and just need decks clean up $ 350.00 would like it to be pick up in maryland 21783 but if you want to pay to ship it you will have to set that up. i will...

Mopar 8 3/4 small yoke fine spline with Moroso girdle race caps. caps screw in and also have lock on end of bolts for extra hold. $75.00 plus $8.00 shipping

will pm you

pete please let me know if you don't want it and i will pass it on . Thanks joe

Have the dip stick and tube $10.00 will have to get you a shipping price will look for spring .

just sold distributor today

also have flex plate , fuel pump looks new but i would have to test it $3.00 / motor mounts / fan pulley /crank pulley/ oil dip stick with tube/ timing cover /oil pump/

yes lifters are stuck to.

1976 Plymouth slant 6 short block locked up from sitting 1999 to 2021 moisture damage. IF you see a part on this you can use let me know most parts $5 to $10.00 plus shipping oil pan $20.00 if you need a piston or rod i will try to get it out .