Search results for query: *

We had a 325i convertible that I wanted to swap a small block with a 5 speed into, with side pipes, roll bar, flared fenders and big ol wide tires and a blower sticking out of the hood. Wife wouldn’t let me dangit.

i just took the one off my 73 Duster and on the backside where it screws into the hood there is zero corrosion and its real shiny metal, almost like a zinc brightness to it. maybe different years used different finishes? there is no signs of black phosphate on this original one owner 73...

Went to work this morning and the power was out, so screw it came home.

Next , is your pan leaking or your rear main seal? I haven't had a problem with the rear main seal before, but do now. Just duplicating what I have done in the past, and it's not working.

...Nationals is scheduled to start at 4:30pm EDT (1:30pm PDT) on Friday, April 26. nhra.com currently shows the following number of entries: * 17 Top Fuel * 16 Funny Car * 23 Pro Stock * 19 Pro Stock Motorcycle Those counts are always subject to change so make sure to check to make sure your...

Oh! I misunderstood what you want to do- you want to temporarily hook the system up to the manifolds for a test stand? In that case, you could use the type of ball flange that you referenced above, and just put an elbow on it to connect to the pipe/mufflers. But to use a ball flange on a...

I used my leftover Volvo-Penta outdrive paint on this old crusty gem..........

I have tti headpipes coming in the next couple weeks. I thought there might me a temporary(read cheap)solution so I could fire off in the next day or 2.

It's long since been repaired.

Just to update this thread, I ordered a basic Dampener from Summit crossing my fingers it would be a press fit and not a bad crank. Didn't have time for a full install, but yesterday went out to the garage quickly and tried to slide it on the crank snout- it slides on by hand the first bit, but...

Thanks Steve. Sorry for calling you Troy. Bill and I were talking about a Troy and it just kept coming out!

I started volunteering at Food bank about 2 years ago. Mc Ds was right close and I ate my lunch in the vehicle. My go to meal was the double quarter pounder with cheese meal. Came with medium fries and medium drink. Cost was $12.48. New owner took over. An immediate increase to $13.66, then...

Now I see as well. lol. Someone sells the 2 front pipes. I forget who. I have them on my ragtop Exhaust_Parts lol again. someone already posted but read top of page. You tell them what maifolds you have.

If it would have had an air grabbing six pac hood on the car it would have flipped over on its roof.

Morning, last nice day here, we have rain moving in and getting colder with rain totals going up for the weekend. Had a show to go to an Saturday at Lincoln Tech.

I think there was a thread about the OD and ID of bushings not being correct tolerneces for press fits. Lower control arm bushing slides onto pin

Yep, air got under that crappy looking cowl hood and did what air does...

I tried contacting you via personal message but cant.?

WOO HOO YEE HAW, it's gonna be a great day. Be safe and have a Freakin' Blast!

Confused, says ethanol free but says 10% ethanol under the button.

Now I see what your needing to do! You could see if an exhaust shop has some 2 1/4" two hole flanges that will bolt to your manifolds, and get them to weld you a piece of pipe to them in a way that you could hook to them. Places that do exhaust work always have stuff like that in a scrap pile...

On a 4160 Holley (vac sec) There is still a spring kit of 10 different springs to adjust the opening rate of the vac sec diaphragm I've seen 750 , 4160 's tuned with the springs that you could barely detect the opening of the secondaries

I pick up a few more very hard to find 67 to 70 Duster Dart Valiant Barracuda NOS Disc Brake Master Cylinder part # 2808600 casting # 2225541 Mopar These are correct for power or manual Disc Brake Black paint might need to be touched up a little bit 250.00 pick up or plus 10.00 shipping

I'll be right over (or down I guess) Save me some breakfast and I'll bring some bourbon.

That explains it very well. I think this is an excellent mod as I have the same setup , centerforce, etc as you. I will definitely be doing this in the future. Thanks so much for the tech and advice, Cheers!!

All this talk about brekkie, I am cooking for some guests this morning. Here is my “prepped” menu for when they come up the hill, not pictured are eggs and biscuits. Fried taters for the win! Merica! They stayed in the apartment last night at the shop. Bourbon was flowing when I gave up and...

Well it was bad, but certainly fixable.

Forgot to mention what I did there. The factory rods connect to a "mushroom" head type stud. They easily knocked out of the z-bar. I think they were just pressed in and not even welded. (aftermarket z-bar). The pedal was another story. If I remember correctly, I had to cut the head off and drill...

Probably couldn't afford McD's. I know I can't.

Don't forget to adjust your timing after you get the carb dialed in. And then re-dial in your carb. And then re-dial in your timing.