Search results for query: *

Well stumbled into an odd situation again. I am thinking about replacing the skin on my from bench seat ('75 Duster) because it has several ripped seams so I started to look at where I could buy them... I didn't think this would be much of a problem.. The car is Golden fawn ...I am not sure...

Anyone can tell me how the dome light is installed. daughter took it off and has no idea how to re install :( Nothing in the manuals. I see 2 screw holes in the car but nothing on the unit. Thanks Ian.

Looking for pictures of: 1) How the car jack is installed in the back, passenger side of a '75 Duster trunk.. 2) and pictures of how the carpet should be installed. I bought "fitted" carpets that "might" need a bit of cutting. Heck, the car could be 8 inches wider and the carpet would still...

Just noticed a small crack (1/2 inch) in our dash pad cover in the corner. Is there any glue or something that we can apply so it won't get bigger ? Thanks Ian.

Folks, I need to glue vinyl to wood..I tried the 3m spray glue but it doesn't hold very well. Suggestions ? When you laid your new interior carpet in you car, did you glue it in or just lay it in ? Thanks ian.

i have come to the conclusion that my fabricating skills are not up to installing the seats I have in the car so I shall start off at scratch one again. Looking for a set that can be in stalled in a duster that has excellent neck protection...and easy to do. Recommendations ? ian.

I am putting together a new instrument panel and have been looking for lights for the blinkers and high beam.. I would also like to put a few leds in the foot wells, etc to light the interior of the car nicely at night. Has anyone done this and could you recomment a vendor ? Thanks ian.

Are there any metal fabricators out there in FABO land ? I am installing non mopar buckets in our '75 Duster. They are 20 inches wide at the front so I know they fit. Unfortunately, the track is 18 inches wide (Duster tracks are 12 inches hole to hole) so I am looking at the following...

I need to remove my interior to change the colour however, I am concerned about going too far. I didn't see anything about removing the dash ... is it a hard job to put back on properly ? Should I leave the headline in and spray it where it is ? Thanks Grassy

Folks, I want to change the inside colour of the car to black from tan. I am looking at the company Parasol for their dyes. Has anyone used them before ? Any experiences ? Their web addy: http://www.parasolinc.com/ Thanks Ian.

Could someone with buckets in their A body please measure the width of the seat cushion ? Thanks Ian.

We pushed the Duster outside just awhile ago and have a couple of good rains...and i discovered puddles on both floors. I don't see water getting around the windshield and I opened the air vents thinking the water may have come from there. I my old british car days...stuff would get into the...

I am cleaning out the interior of the '75 to paint and there is this thick rope of sealer on the corner of the floor/rocker panel and other places. It comes off with a flat edged tool quite easily. Is this seem seler or carpet glue ? Should I replace it or can just leave it be..it almost looks...

Folks, Wife floored me the other day when she said she thoughtthe kid's dudster carpers were too worn to clean/dyd and we should buy new ones. Huh ? Checked locally..$ 3-400.00 plus tax. On E-bay E-bay User mcp-313 Cost 165.00 Our Carpet Kits are made in the Good Old USA.. : Brand new...

We are going to be changing the interior colour of our car..I do know that PPG has a three part staining process for all the plastic but the steering wheel has been puzzleing me..do we just stain it as well and will sweat take the colour off ? Thanks Grassy

I am not sure of the correlation between Chrysler muscle cars and fake wood trim. I have driven cars with real wood trim but I think fake wood it is really out of place on these beautiful cars. For those owners that think like me..how did you eradicate this fake stuff ? Any pictures ...

Folks, our '75 Duster interior is tan. We are changing the colour after all theother work is done. ..we would like it to change to black. My wife would prefer the interior to be replaced entirely but I am operating under a very limited budget I would prefer to paint the interior (and all...

When you shift over from bench to bucket seats..what do you do with the old mounting holes ? Is there a plug that going in the hole ? I was thinking about two small metal plates, some caulking and a small bolt..then a rattle can to paint it....what did you guys do ? ian.

Knowing my daughter, I wanted all the guages in front of her..not down by her knees and I wanted to convert he speedo over to kilometers.. I saw the really fancy - read expensive - clusters and decided to make my own. One of the problems is and just like others things in this car is that the...

Hi, I bought a set of non mopar buckets for safety even though I had a set or originals to restore and install. I assumed that it could attach the new buckets to the existing sliders and bob would be your uncle. Anyway, by eyeballing the mopar sliders in the car, they didn't look flat so we...

Folks, I am going from bench to bucket. On the right side, The carpet is actually cut where the hole should be but don't feel a divot or plug where the original bucket holes should be. I understand the all bodies were built the same and didn't drip out the sports that were not needed. is...

Folks, I want to change the interior of the car. My wife thinks that if we change the colour to black with the kits to spray on paint to the dash and pad and dye for the carpets that it will look like sh**. Is she right ? Grassy

Folks, We are trying to make the '75 Duster as safe as we can...I suffered quite a neck injury in my old '96 ram ...the head rest didn't go up far enough..really buggered my c-4, c-5, c-6 and I would want my kids to suffer the same and even though we have a set of mopar buckets, we have decided...

Can I convert our '75 duster rear end so it would fold down...what do I ned to make this happen.. Thanks Grassy

Folks, We have all the fixins to put a new set of a body seats in the duster...probably would do it too if it was my car but honestly, my kids are piloting this car and I don't think the old a body seats are safe enough..especially after the neck damage I incured when I was rear ended in my...

Not sure if this is a dumb question but we will be moving from bench to bucket, do I have to change the mounts for the seat belts or swap out the existing belts ? Thanks Ian.

I think Plum Crazy is right. I have the sliders and metal seat frames..I was going to buy the foam and have the local upholstery make/ install a set of seat covers..he didn't tell me the price when I was there but I think it is going to be high...and unfortunately, what you get is a set of foam...

Folks, I want to give vs always take from this forum.. I ran into this company last week. Found this company...they work with companies like Rolls Royce...their products are awesome...didn't know these guys existed.. http://www.parasolinc.com/ Support is wicked fast..e-mail this guy with...