Search results for query: *

I am looking for the AC/heat vacuum actuator that is mounted on the heater section. It is connected to a small bell crank and operates 2 doors. This is for my 69 barracuda w/factory AC. I have a broken off stem and would rather replace then try to repair. The rod is approximately 4".

I need a set of front bumper brackets for the 69 barracuda. Will be shipped to 19320.

Looking for an adjustable spring tabbed throttle rod like the one in the picture. It is going on an RB install in a barracuda.

Looking for the cover for a big block 727, no damage or cracks. Correct hardware a plus!

I need a wiper arm clip like this. came off my 69 fastback

1969 barracuda ignition switch. I dont need bezel or tumbler. Great condition or NOS would be good. terminals are loose on mine. Intermittent drop out of battery feed. picture included. source to purchase from vendor also welcome.

I need 15 original clips for windshield trim. I have aftermarket type but want the original clips. Picture attached. good screws a plus but not required. shipped flat rate to 19320 should be easy enough.

looking for a source for the correct clip studs for the 1969 barracuda trunk finish panel. I found incorrect ones for 70-82 bucks a set. Top picture, too long, 14 required. excellent used ones considered.

looking to see if an exceptional wheel is out there. Black textured finish, no chrome band around the rim. I have all the other parts and a wheel I doubt could be restored. Below is picture of one I restored for my 67 fsb

Looking for a complete column harness with turn signal switch for my 1969 barracuda. part number removed is 2857 241. Would like full deal with connector if possible but not a deal breaker if connector contacts are good. shipped to 19320

I am looking for a factory black steering wheel for my 1969 barracuda, excellent condition would be great, with horn ring and button. whatcha got? shipped to 19320.

I need the black plastic slide that covers the shifter slot next to the shift indicator on an A body console. I have attached a pic of all that is left of the one I took out. Will buy complete indicator if that is needed to get part. :thankyou:

Looking for a pushbutton type A/C heat controller for parts. don't need the push buttons, vac. switch, or fan switch, just the slider guide part.(plastic) Let me know what ya got!

I need drivers side roof drip rail trim for a 69 barracuda fastback. must be excellent. Message me the price- shipped to 19320, Coatesville PA. I only need the one piece.

looking for a dozen of these. A source would be great. filister head sheet metal screws, phillips head about 5/8 long. used to mount rally dash among other things Thanks!

I have a broken pin on the heater control. looking for a heater control for parts or complete for replacement. Don't need cables

I need the wiper motor connector, not the bulkhead connector. don't need a full harness. PM price shipped to 19320 Thanks!

Anyone have a set of the metal hood clips for the insulation pad? Would rather not purchase plastic ones. Need a full set of 18. A re-pop would be good but haven't located any. Thanks in advance.

Mine are simply missing from the 69 barracuda I just bought. I imagine these aren't reproduced any where? shipping to 19320

The "NOS" 340 bars I purchased from a member are not NOS, slightly curved, and one has a nice impact mark, quite deep. (inbox for member is full) don't wish to flame. Soooo, I am looking for a set of 892/893 bars to CARLISLE. I have the old bars, (straight), if interested in trading. For a 67...

Rusted out UCA area on left frame rail too sketchy for repair, so looking for drivers and maybe passengers side frame rails for my 67 notchback. I am not sure of which years work but I believe 63 to 72 are the same...chime in if you please! why oh why aren't these repro'd....thanks for looking...

I need a couple of good door striker posts with good rollers, not deformed or sloppy. I don't want to buy the ebag crap. Going on a 67 barracuda. Pm a shipped price please.

Putting out a feeler for complete A/C system for my 360 notch project. Looking for all of it down to brackets and hardware. Under the hood and interior parts needed. I really don't want to piece together parts that compatibility is questionable. Condition warrants price.

looking for 67 barracuda vinyl top trim complete. and S/S wheel well opening trim.

Top of passenger door stainless. must be in good condition. no dings. I will need pictures and price shipped to 19320.

I need the left front fender metal splash shield for my 67 notchback barracuda. no rot. may buy a set if price is right. will be shipped to 19320. I will need picture to ensure it is correct

I am going to convert to power steering on my barracuda and need a coupler. PM a price shipped to 19320.

I need great condition A pillar moldings. no cracks, and holes good. Putting them in my 67 notch Also looking for sail panels in excellent shape.

Looking for a set. Casting numbers 3614368 3418623 Reasonable with good mating surfaces (Don't want to use a 621 unless I have to).

Looking for a set of deck lid trim, upper and (correct) lower. premium price paid for premium pieces. I don't want to go the repop route if I can avoid it. I have the center panel.