Search results for query: *

So I dropped in my fresh 360 along with a rebuilt 904 and 8 3/4. My problem is that in idle or when I have it on jack stands it runs great. I can pull rpms and the throttle response in awesome. Now, when I pull it out onto the street I can't pull anything beyond 2500/3000 because it breaks...

Would a starter out of a 2002 Dakota work as a mini starter in my 360 LA? Thank you.

So I ordered up my ARP flex plate to crank bolts #240-2801. The bolts will not seat all the down, seems they are 1/4" too long. Any ideas on what could be wrong?

I installed the balancer on my 360 and when turning it over by hand I noticed the damper kind of pulls away at one point when watching the damper come around past the timing marks on the timing chain cover. Moves 1/16 of an inch or so. Is this normal? Thank you.

I picked up a 360 short block and as I go to install the harmonic balancer with a piece of threaded rod to draw the balancer in, the threads stripped out. Not sure if it was like this or something I did. Anyhow, besides pulling the crank is there another way to repair this? The engine is...

What size bolts do I need for mounting flex plate to the crank on my 360? Thank you.

Is there a way to bench test a mechanical fuel pump?

I installed a new cam and timing chain set in my 360. When lining up the dots on the cam gear and crank gear should the #1 piston be at TDC? I haven't done this years and need a refresher. Thank you.

Is there a cam out there that is equivalent to the 508? I've got one in a 360 short block that Im putting together and thinking of going with a different brand with the same specs. Thanks.

I need a set of crank offset keys for my 360la. Where can I find these? They usually don't come with timing chain and gears set do they? Thanks.

Do all double roller timing chain / gear kits have degree notches?

How tight is too tight for a distributor shaft in a distributor bushing? I installed mine with tapping it in with a wood dowel. The shaft goes into place and turns fine when meshed with the cam gear. If I try to remove it with a screwdriver it doesn't back out like I've previously...

I'm throwing together a 360 and wondering what you guys think and where I should change things up if needed. Also any HP estimates would be welcome too.:cheers: Fresh 360 with stock crank/rods. KB 107's MP 292/508 cam 587 heads with 202's with home port work done. Stock stamped rockers and gear...

How many pins are used for each head? Any part numbers? Thanks!

When mounting a oil pump in a LA 360 is there a gasket involved or some kind of sealer?

Anyone ever use the Summit brand oil pans? I need one for my 360 and just wondering how the fitment is. Hopefully they are not as bad as the cheap chrome ones you see on Ebay for bucks.

Which way is the filter supposed to face when using a 90 degree adapter? Pics would be nice. Thanks!

I'm going to seel up the bottom of my 360. Should I use a gasket,The Right Stuff or both? I'm just looking for opinions from people who have been there,done that. Thanks!

I'm going to be mounting my oil filter plate on my fresh 360. I don't want leaks (obviously). What type of RTV should I use? Thanks.

I picked up a 360 without any specs or not much informationon it. I pulled the oil pan and looked for numbers under the crown of the piston. I came up with a 11116 on one side of the wrist pin and a 030 on the opposite side of the pin. Any idea on what pistons these could be...

Isn't there a spacer used between the stamped rockers on the 360?

I'm going to be swapping my 225 for a 360 using the schumacher kit. Which oil pan will I need? Thanks!

I'm swapping a 360 into my 74 Scamp. Which oil pan will i need. I have one out of a 75 RV that looks like a rear sump. Will this one work? Thanks.

Anyone have an idea of how much to have a block hot tanked,cam bearings,freeze plugs installed and line hone done? Thanks.