Search results for query: *

Before I decide to purchase a new wiring harness I thought I would check the one ithat was in the car and an extra one I have. Anything I should know. Best way to clean ECT.

Would like to test a few switches before putting everything together. I know the switch to the heater was bypassed to a toggle switch. Any thoughts

I have my 65 Barracuda disassembled and am checking things as I head towards reassemble. Is there a way to check the individual guages that are not installed in the car. I'm trying to troubleshoot things as I go. Highs in the mid to upper 90's will keep me from painting this week. Doing small...

I have a newer circuit board to replace the old one in my 65 Barracuda. Is there anything I should use or do to clean any contact points as I change from my old one. I am using my old gauges. The old circuit board had a crack in it and the gauges were not working. Hopefully this will solve my...

I have had this for a while an need to install it. This is for a 65 barracuda. I lost the directions. Does anyone have a picture or tell me how to hook it up. Many thanks

It's not an A-Body, but my son bought a 95 Dodge Ram truck. The dash lights are out including the check engine light. The fuse is good and the headlight switch is new. I replaced the bulbs also. What should I check to make this work? thanks

A few weeks ago i removed the gauges from my car. when I put it back in I had no power to anything. It finally started working after I took it out and put it back in about 10 times, Today I removed it again to replace the voltage limiter and again I have no power. I have 12 volts at the red wire...

This morning I removed the guage assembly from my 65 barracuda to replace some bulbs, the voltage limiter and clean the contacts to the lights. When I put it back together everything is dead. I have a red wire a black wire and a plug that has 8 wires. The red wire has voltage. Nothing else does...

I need some help. I just got my 1965 Barracuda Formula S started today and the tach isn't working. Any ideas about what to check. It is a factory dash mounted tach. Thanks for your help.

How can I clean the old alternator to make it look better? I took it off the car and the exterior looks old and dirty. Is there a way to clean and restore it? I don't need it to look new, just better. It works fine so I don't need a new one. thanks

do the dash lights operate at 12 or 5 volts. I need to order the voltage reducer because the guages are not working, but was hooking the lights up and found the dash lights don't work. I thought they worked before but as usual, I could be wrong.

OK, I know this is suppose to be simple, but I'm confused. I was going to replace the voltage reducer because the fuel and temp guage doesn't work.While checking things I don't have any power in the fuse box where it is marked instruments. Would this be my problem or is this another problem...

Good Morning I am working on a 65 barracuda. For some reason I have lights on half of the dash but not the left side. Also the fuel and temperator guage will not work. As I look at the back there are only 2 wires a red one and a black one. I forgot about the other plug which I believe supplies...

how do I remove the knob. The windshield knob had a set screw. I am removing the dash cover to recover or buy a new one. Thanks as always, Tommy

does anyone know anything about the old radio. mine is a 65 barracuda that i'm working on, and I found the radio in the trunk. a lot of the car was disassembled when I bought it. my question is I plugged the old am radio in the existing plug and was surprised the light came on as soon as I...

thanks to all who offered their help. followed the advice of all, but found the culprip was the socket was warped and wouldn't let the light bulb sit straight in the socket. I was going in and one prong was in place but the other was not far enough in to turn. again, many thanks to all Tommy

I am restoring a 65 Barracuda that has a lot of rust and corrosion. I have used a cleaner on the different connections and replaced all of the bulbs with good results till now. I took the bulb out of the front signal, cleaned the socket but can not put a bulb back in. Actually I can put it in...