Search results for query: *

I have stock everything on my Demon340, 8-3/4, new brake lines, new hanger clips, stock dual mufflers, stock brass axle Tee Block, stock brake line bracket that holds rear drop hose that mounts on the topside of the muffler hanger bracket. The stock rear brake drop hose does not reach the tee...

My local Autozone & O'Riely's tell me they don't have a source for RIVETED rear 10"x1.75" brake shoes! Does anyone make these now? Thx ahead

Who has the most/best complete resto kit of rear 10" drums brake parts? While the backs are apart it would be a good time to totally replace everything. Thanks

So I really need that little rubber seal at the end of the rod. This one goes in but when I try to pull the rod out...it comes out by hand....and it shouldn't. Somebody has to sell these. Any help is appreciated. Thanks.

Where can I get the little rubber seal that goes on the end of the brake pedal rod that goes into the back of the master cylinder AND the rubber boot?

So which direction does the open end of the disc brake seal go? Does the open end go towards the engine? You/I can't tell by the Service Manual print. Thax

4" Drum setup is off and now the reassembly of a 4" KH non-power front disc assembly starts. My problem, I can't find a step by step instruction. Can anyone suggest a link or video to watch? Thankx

Lost everything off my old laptop and I could use this. Has anyone done an article on a 10" drum swap to 4" KH Disc? thanks

Converting 10" Drums to KH non-power Disc and I have old MC off so what's the easiest, cleanest way to flush the lines of the old, very dirty fluid? Thx

I picked up some of the REM bare metal product and it works great on some fender brackets. Anyone have pics of it on brake parts? Thanks

I picked up a complete emergency brake system from Inline Tube because it was a great show price. Anything I should watch for or watchout for when replacing the old system? Thanks in advance.

Want to get rid of black paint job on MC and paint it cast iron gray. How do I preserve the gray cast look after it's installed? Thanks for your tips.

So i've been told switching over to DOT5, you have to drain the complete brake system, disc/drum sbp, and then flush the system with something. What should I flush it with? Thanks

Could this vent be leaking? If so, do I replace the whole thing or just the vent? Does it just unscrew? Thanks

After you blast and straighten disc dust shields, what would you do to make them as new original looking as possible? Paint, powdercoat?

Does anyone make these rubber seals? RockAuto shows only ball joint w/ seals....just want new seals. Thanks

These are the L-shaped bracket that mounts on the side inner fender where the hydraulic hose goes thru. Anyone have a couple or know where to get them? Thanks

Does anyone still make OEM exact bolts to bolt KH calipers on to the steering knuckle? Thanks

After I blast the brake parts, should I paint (with what) or powder coat? Medium gray? thanks

Who or where can you get one of these? It's on a KH 4"sbp front disc setup. It goes on the steering knuckle before the splash shield goes over it...Help, thanks

Anyone have an OEM front disc nonpowered KelseyHayes setup on their car? Which master cylinder do you have? I want to convert back from drum brakes. Thanks

Any tips on how to get my used dust shields to look closer to these? Thanks

Is it possible to take a new dust shield for a 4 1/2" boltpattern and oval the bolt holes so it will fit 4" sbp ? No one makes these new for a 4"

Has anyone got a link or a parts list to convert a front drumbrake car to KelseyHayes 4" disc. I have started collecting the parts for a 71 Demon winter project; i need the parts list. Thanks again.

Let us all see which master cylinder you have ONLY if you have non-power front disc brakes...thank you from many.

When I convert my 10" drums on the front to KH non-power disc brakes, will I, should I, could I keep my current master cylinder?

I just found the webpage www.primoclassics.com for an exact (claims) copy of the '71 prop valve for a disc/ drum brake setup. Does anyone have any feedback on Primo or the prop valve? Every other valve seems to be brass.

Does someone have a pic of the correct manual disc, front, prop valve used in 1971 or can I use my existing valve and master cyl ? Thanks

I have sbp drums on the Demon now. I am redoing sbp KH disc. Will the UCArms work on the disc brake setup? Thanks in advance.

Who sells the short crossover lines? Thanks