Search results for query: *

Valiant Signet with a gas cap body trim around it. Never seen one before did they come on all Signets?

This thing is looking pretty bad a$$! http://bangshift.com/blog/category/project-cars/mopar-projects

A quick scan of craigslist provides the proof http://losangeles.craigslist.org/lac/cto/3283310178.html

http://losangeles.craigslist.org/wst/cto/3101160681.html Pretty clean looking early A. I would like to see a nice early A like this one run through Barret Jackson Auction during prime time. Car like this might be able to pull down some cash.

This 66 Formula S I'm working on had two tin straps that held the heater hoses together from the factory. I have lost them and would like to replace them. Anybody have some in good condition or is there a reproduction ones available somewhere? Just for clarification not talking about the clamps...

Found and bought a 1966 inland 4 speed shifter and handle. Anybody have tips or diagrams on how the rods go in? Well I have the rods in but not quit sure how to get it adjust or set up. Might have a rod going in on the wrong side on bottom of the shifter, seems like 1-2 and 3-4 might be binding...

Need to set timing and dwell on the 273HP with clean air package and manual trans. Not much experience with the dual point distributor I guess the dwell should be double the book setting for a single point is that right? My book says timing 5 degree after TDC is that right? My book only...

Here is two pictures I borrowed from toolmanmikes car and one from oldschoolcuda. Hope you guys are ok with that. Both motors and engine compartments look great and thats why I have used both these picture when putting my engine compartment back together. Without even thinking I hooked up my...

I have heard that the correct color is red. However my motor that was standard bore and appears to have never been apart before was more orange than red. Everything on it even the bell housing had a much more of a orange color than the red Mopar paint I used to repaint it. My 66 is an early...

Putting the engine back together and wondering if the two items in the squares below are from the factory. Item 1 is a plastic 90 degree fitting that goes to the power brake booster. Item 2 is a some timing device I suspect this may of been installed later to comply with California smog...

Just blasting off some oil and dirt off my 1966 small block 273 motor mount brackets. I didn't see any signs of paint or coatings other than oil and dirt. Was going to coat or paint them, but if they didn't come factory painted thinking I might just leave them as is. Thoughts?

Looks like I get to do some grinding

Might remember my ugly 66 (thats just her nickname) Well it's been parked since 1982. I have it running and stoping now but it loses water out of about three freeze plugs pretty bad and one is behind the flywheel. Going to pull the motor to replace the freeze plugs. Then pull the pan replace...

Even scoring a few good deals this long term project is taking me to the poor house. Getting close to droping in the motor and trans in. It's only been 5 years since it was painted. Makes me think about the thread will my early A ever be worth what I have in it. Seems like after I turned 40...

I can say that since I have owned a 66 Barracuda since I was 15. That would be 25+ years. Well another has found it's way in to my life. I'm going to go outside and unload and take some pictures for you early A lovers. Be back in an hour or so.

Had these new TTI headers coated black. I think the silver is just a little over done now days. Interesting is the fact I guess they don't cook this coating just spray it on and air dry. Suppose to be alot better in the higher heat range can't remember numbers but it was like double the rating...

So I bought the rubber gasket and new lens from Rick@Layson for my 65 Valiant tail lights housings. I had also bought the foam gaskets a long time ago for the rear tail lights housing. Not sure if the rubber goes on first then the foam or the otherway around. Anybody know? it would be a shame if...

I decided I would never get this car back together if I didn't start working on it. The rain also help give me some garage time. One small project at a time and the front end was first. Had some wilwood brakes setting on the shelf for years and ordered up some ball joints and bushing to do a...

I bought this 1966 Formula S Barracuda. When I removed and was checking out the fender tag there was a small hole in the shape of a perfect S that was punched through the tag. I was wondering if anybody else may have seen something similar on there 65,66 Formula S tag. I had a 68 Formula S...

Who has replacement front and rear floor pans for the 66 Barracuda? Anybody have pictures of a install?

65 Barracuda seat upholstery. Where is the best place to buy factory reproduction seat covers? Would like quality first then best price.

Any tips or instructions on front and rear window installs for 65 Valiant. Never done one and the paint shop had disassembled during paint. Is there any clips or just the rubber gasket? Does the gasket get put on the car first or around the window during glass install? I have install truck...

moparlee requested some additional cage pictures so here they are