Search results for query: *

So I happen to have a 545RFE trans here at the shop and I'm wondering if I could use it behind my hemi. Is this trans easier to control?

Hey guy's I have a buddy that is going to be making me some valve covers and an intake for the Scamp and he's wondering if he should make a jig for them so he can make several sets. What would you guys think if he can do them for a real good price the interest would be for these items? Intake...

Can someone measure the intake manifold for me I need to see how High I can go. I need front the mating surface of the head to the top of the intake at the front.

Hey guys just a quick question since I know most of you guys are running 5.7's and 6.1's in stock configurations has anyone dyno'd their combo's? I know what these engines can do in a New LX vehicle with all the computer BS fighting them so I'm wondering what happens when you bolt one of these...

Hey guys I have access to a couple of new hemi stroker kits And I have built several in the past (some pretty high hp ones too) So I was wondering if anyone wants to do a nice big cubic inch Hemi's for their swap projects. If this sounds interesting to you PM me for prices I can build the 5.7 to...

I do. Ok guys if you are going to be running a factory pcm that has been flashed before and was in a car please pay attention here this will only hurt for a minute. The factory system use a module that hangs out behind the ignition switch and it sends a signal to the pcm telling it whether or...

Guys I finally got through to Diablosport and got my CMR tuning software reactivated with my new laptop I had locked my last ip address from them. I can handle most MILD changes like injector scaling ( using 5.7 with 6.1 injectors I can adjust the fuel trims) I can turn off tcm's I can disable...

Sound like the security module to you guys? I fed 12 volts to the PCM and the throttle body hunts for home and the asd relay powers up but she shuts right off. I'm not fully wired yet so I don't have my ALDL connector wired up so I can't hook a scanner up yet so I don't know if skim is enabled.

SO I've been tossing around the idea of forcing my Hemi to breath with an artificial lung. I was going to go Pro-Charger since I already have the brackets But I haven't turboed a 3rd gen yet and I want to see how she would do with 20PSI. So my question becomes should I do a single front mount...

Ok guys I am doing loads of research for my Hemi build and I figured I would post up my experiences to help some guys make this swap in their cars a bit easier. I am not finished so this thread will get updated as time goes on with new information bu tI will try and post everything I have found...

Ok just got off the phone with my dealer and he is telling me the 05 truck pcm can only be activated with the starscan once and cannot be reflashed. I call B.S. but I can't say that to their face without proof so is anyone running an 05 truck pcm in their hemi project?

SO 5.7 Hemi sent me the factory harness he had and I spent the better part of an hour ID'ing connectors and labeling them does anyone have an idea of what needs to stay and what can go? I pulled a power distibution block out of a 3.5 charger with the plugs and relays so I will use that for my...

Well I managed to get 70% of what I needed today to get my wiring sorted out BUT there are a few things I could not find in the junk yard here(mostly older models) I need a few connectors for my harness. Throttle body connector Map sensor connector Cam and crank sensor connectors 03-05 coil...

Hey guys I'm on a tight a$$ budget and I need to fab up my own mounts. I will be using the stock rubber isolators and doing something similar to the TTI set-up but with some added strength to the passenger side. I have enough steel to do a few set's and I was wondering if anyone would be...

Well I have been looking on the craigs list thingy for a few weeks after my last 5.7 fell through and I have finally found another smoking deal on an 03 truck motor. Has a slight rod knck but with my plans of doing a 392 Stroker this doesn't bother me one bit. SO I will post pictures when I get...

Got a guy parting with 2 5.7 hemi's both water damaged by the storms we had here but they are supposed to run (one has low compression and the other is slightly knocking) I dont see 1 hemi for 1g let alone 2 But I don't need to engines so if we were to split the cost there could be 2 hemi's for...

Well I just got the word from E-Bay that I won my auction on a 5.7 Long Block now where do I need to go from here? I will be going Carbed for now the injection will come when the budget permits. What all do I need as far as my chassis is concerned? I know I need the TCI motor mounts but what else?