Search results for query: *

Complete set of Rear 9" Brake stuff including: 2 Drums Axle Set of shoes Springs, levers adjusters, hold downs, etc, From a Running and driving & stopping! car 10/2023 No Wheel Cylinders or Backing Plates. $20 OBO Plus Shipping from 15642 I doubt there is much interest in this, but if someone...

Yellow 33 Tooth Speedometer Drive Pinion Asking $15 plus Shipping from 15642.

Black 29 Tooth Speedometer Drive Pinion Asking $15 plus Shipping from 15642.

Green Drive Pinion 34 Tooth. $15 Plus Shipping from 15642

Choke Pull off, I am not sure what it is off of.. It works and holds a vacuum on the "straw test". Asking $10 + Shipping from 15642, PA

Speedometer Pinion gears $20 Each Plus Shipping from 15642, PA (1) Black 29T (2) Yellow 33T (2) Green 34T 8.75" Center block and Roll pin $10 Plus Shipping from 15642, PA

This exhaust elbow was on a Forklift. It has been blasted, painted, and ready for your project. It could be used with some sort of turbo project, the exhaust tubing is a slip fit over the end. It is cast iron and will bolt to the Bottom of a Stock Slant 6 Exhaust Manifold. Asking $15...

Here is a nice E brake Cable Equalizer. I am not sure what years this fits - '67-'76 if I had to guess, I had it as a spare for my '69 Dart. I no longer need it. It has been blasted and painted and ready for your project. Asking $20 Plus Shipping from 15642, PA to you.

Here is a nice, complete OE throttle pedal linkage for '60-'66 Mopars. Everything is free and moves properly for your 1 Barrel Slant 6 car. Includes OE Clips and requisite parts. Asking $20 OBO Plus Shipping from 15642, PA.

Hello, here is a nice Offenhauser Dual 1 Bbl Intake with (2) NOS never been used matching Carter BBS № 3278S carburetors. The throttle linkage is sorted and installed works and moves freely, and is adjustable from curb idle to WOT. A bracket for the transmission kickdown linkage is included. (I...

Hello, Here is a Set of ARP Con Rod Bolts for a slant 6. 2 Sets, - 1 New, Sealed in package, - 1 Opened , then resealed, Open box, has all proper parts, never used. Asking $50 each plus shipping from 15642, PA to you.

Used MagnaFlow 13219 3" In and out Reversible Offset / Center Stainless Muffler. Part is used, but I have cleaned it up in the blast cabinet. No internal or external rot. Pipe Ends are good and not crushed from crappy clamps. Loud muffler. Asking $55 plus Shipping from 15642, PA Sorry I...

Asking $350 Plus shipping from 15642 Can Also Bring to Carlisle this week. (7/12-7/13) Good, Clean, Running Carb, reset to factory Specs. - 51 Primary Jet. - 6.5"Hg Power Valve. Carb ran fine on a stock Slant 6 with no other mods. , I just went a different route for my project. Carb is...

Driveshafts for Sale $20 Each Plus shipping to you from 15642. No Trans yokes included even though there are some in the pictures, those are removed now. Lengths from 54 1/2" to 50 1/2" All are the "Small MoPar" 7260 2 1/8" U joint size on both ends. All of these shafts were from various A...

I am not exactly sure what these are for. I know they are from an LA Engine and they are brackets for mounting front accessories. Possibly Alternator support or part of the RV2 / c171 Compressors? Cleaned and blasted ready for your project, Asking $20 OBO plus shipping from 15642 to you...

Here is a cheap spool: A Welded open diff with berarings and races for the 8.75 / 8 3/4" Rear Asking $50 OBO Plus shipping from 15642, PA I have cleaned it up and every thing looks as it should for this type of part. The welds are all cracked from use, but it does not turn the spiders/ side...

Cleaned, Blasted and ready for your project: Saginaw Style LA Block Power Steering Pump Brackets $10 Plus shipping from 15642

Slant 6 Car (9.25/10") or light duty truck clutch cover 122T flywheel. It is the Large Hub for 1968-1987 Engines. Will fit a 1960-1976 Engine with an adapter ring (I Have one of those available too for a separate fee) Cleaned , blasted and ready for your project. I recommend getting the...

Speedometer gear adapter with factory clip and retaining bolt. Asking $30 OBO plus shipping from 15642. USPS MO or Personal Check for payment. Thank you.

Cleaned Blasted and Ready for your project. Dipstick Tube only - I believe it is from a 727/Big Block combination. $15 OBO Plus Shipping From 15642.

I have A complete Slant 6 (225/ 198 RG Block) Dual Exhaust Setup Minus Headers from a '62 Valiant. Can easily be adapted with some extra bits of tubing for a longer wheelbase dart scamp etc. Setup for use with Clifford Shorty Headers. I cut the tubes a bit short when removing at the mufflers...

Asking $220 OBO. Good Working a230 # 3speed. I had it in my Duster before I built the 833 OD for that car. This is the model that has the synchronized 1st gear so You can shift into 1st before coming to a complete stop. Some of the early MoPar 3 speed s have a straight cut non synchronized...

Hello, Here is a Nice Offy # 5041, Dual One Barrel intake for the Slant 6. It is used but in excellent condition. I have bead blasted it so you are ready to bolt this part on, paint, or coat it without much fuss. Asking $500 and that includes shipping to the lower 48 US states. Please PM me...

Hello, I have a 8.75 742 Case Chunk with a 5.57 Ratio and spool for sale. I found that I had 2 of these and I don't need 2 of them. Could possibly work for some eighth mile setups? Nice part that I no longer need. It has been coated some grease that will easily clean up. Has the 7260 2 1/8"...

I know many of you will never need this stuff, but If some one can use anything lets make a deal. Covers $10 Each. Add shipping from 15642 to all. Misc other parts - Spacers / Shims Ring gear bolts Side and Spider gears Make offer if you can use this stuff. Thanks!

Nice, Clean part with bead blasted retaining bolt and clip. Asking $25 Plus Shipping from 15642

This was from a 318 - Cleaned up for your project. I cannot remember if it was from the Oil filter side or starter side of the Engine. $10 Plus Shipping from 15642

Asking $18 Plus Shipping from 15642. 26 tooth Pinion Gear - A bit rusty on the tip, but who isn't. Wont effect the performance of this gear for you.

Hello here is a Nice, not perfect 727 Transmission Lever set. as you can see in the pictures the parts were a bit rusty but are usable. Threads on Fasteners are presentable but not perfect. Will move freely and tighten on your valve body properly. I Have bead blasted everything, ready for your...

4 Barrel to 2 barrel Adapter Plate Was Modified to fit on a Clifford Intake without Clifford's Adapter Plate - See extra Holes Asking $30 OBO Plus Shipping from 15642 Has been bead blasted and is ready for your project.