Search results for query: *

I have a 318/360 used edelbrock performer intake manifold for sale #2176. Came off my truck last month when I installed magnum heads. It has 1 carb flange stud hole that is missing a few threads but the stud still tightens down as illustrated by me holding the manifold up by the stud. Hole...

I have an Edelbrock performer 318/360 part #2176 for sale. Used in good shape. No stripped out bolt holes. Previous owner installed an ugly giant brass fitting for the bypass. Some of the pipe threads came out with the ugly fitting. New pipe threaded in place and sealed. Doesn't appear to be...

I'm moving in a couple of months and can't take all of my stuff with me. I have 1 318 short block. Looks like standard bore. Previous owner told me it had bearings and rings put in it and an rv cam about 10k miles. I can't confirm this. May run as is, you decide. Free to a good home. I don't...

I have 1 8.75 center section 741 casting 3.91 sure grip for sale. Worked fine when I used it last. Was too much gear for my car. 1 bolt hole for the snubber has been re-tapped. Bolts included. Small yoke. Asking $550 plus shipping. I have a case I can ship it in but the case has to be sent back...

Part number 4120942 . For big block 426,440. I will include the mopar adapter kit to make this fit a 383 & 400.Worked fine when removed. Asking $290 + shipping. $250 without 383/400 adapter. Wires have been repaired. Soldered and heat shrink.

I have a new, in the box, never opened Comp Cams 20-222-3 for a small block mopar. Hydraulic, flat tappet camshaft. I'm not going to use it. They are back ordered from Summit and Jegs. Asking $165 + shipping. Specs are on the box in the pic.

I have been hanging onto this motor to use in another project car but it probably isn't going to happen. Engine came in my 65 Valiant wagon installed with a motor plate. Engine ran great and car was stupid fast. Idled great. Oil was clean. No weird noises. 906 heads I believe. Holley street...

I have a 727 trans for a big block for sale. Trans was in my car when I bought it so I don't know much about it. It has a full reverse manual valve body. Trans shifted firm. Fluid was clean. No unusual noises. Comes with the torque converter. It has a higher than normal stall. Measures right...

I have an aluminum motor plate for a Big Block that I will not be using. Comes with the bolts. It's 1/4" thick. Measurements are written on the front of it (see pic). It was in an early A body (see 2nd pic). No mounting brackets as I had to cut the old ones out but new ones should be pretty easy...

I have a Chrysler performance electronic distributor with tach drive, the cable and a Moroso tach for sale. p/n 4120942 . I believe it works in most big blocks including 426 hemi (do your research). Worked fine when removed. I will not be using as I am going back to small block. Wires have been...

I have a nice center section that I will not be using. 741 case 3.91 gear set sure grip. Worked fine when removed. Asking $450 plus shipping. Shipping will be pricey as it is heavy. I'm guessing about 75lbs. I was going to remove the sure grip unit to put in my 3.55 center section but don't want...

I have for sale a manual steering box off of my 67 Dart. It is a Firm Feel modified steering box. The box is nice and tight. It is a little dirty. I would have to estimate less than 10,000 miles on it as the car has been off the road for quite some time. The box is stamped with a 2 which I...

I have a 318 long block that I will never use and it needs to go away. It came with a dart that I bought several years ago and has been sitting covered up underneath my workbench for about 6 years now. I believe it is a 72 casting. Has a 2 barrel manifold on it. I opened it up when I first got...

I've got a 318 which came with a project car I bought years ago. I believe it is a 1972 casting but I would have to verify that. It will need a rebuild and a bore job. No damage to the engine but it does have a ridge at the top of the cylinders. Located in Indianapolis. I will never use it but...

Making arrangements to pull the slant 6 and 904 trans out of the 72 Dart project car. The wife wants a v8. I am unsure of the mileage as the speedo cable was broke when I got the car 4 years ago. Engine runs good with no funny noises and trans shifts fine too. Both need seals replaced as they...

I have a 727 trans for a small block for sale. Trans was in my 66 cuda when I bought the car. It shifted fine but I don't know much about it. It was a little too big for my car so I replaced it with a rebuilt 904 that I had. Asking $200 or best offer. Comes with the torque converter. I also have...