Car 1967 Dart GT
Roller
This is a major project that I just do not have time for anymore. I am going to put it for sale for 30 days. If it doesn't sell I am going to cut it up and part it out.
I DO NOT have a title for this car. I was going to get one via the Vermont loophole but that has been shut down. I will sell it with a bill of sale to anyone wanting to purchase it.
No build sheet, no fender tag. I have done the DMV search and the car does not show up as stolen or any non sense like that.
I have done a lot of sheet metal work to the car. I am going to try to at least have the sheet metal work finished in the next two weeks. The quarters will not be installed so refinishing will be easier inside the trunk and so forth.
The car is now a roller on a dolly in the front but comes with a lot of parts.
What you will get.
Body
Two hoods
Deck lid
Front and rear seats
Dash
Steering column
K member with front suspension
Grill
Tail lights (not good condition)
Front and rear bumpers with brackets
A/c heater box with all a/c parts that were on the car when I bought it
One extra door I think it is the driver door
All bolts and fasteners that are marked
Any bolt on part that I took off like latches and such
Two front rims with junk tires on ralley wheels No trim rings
I have a TON of parts that will be sold separately from the car. A package deal could be had for everything I had to build the car. This was going to be a 440 car.
Body and above parts $5000
Here is a build thread link to show the metal work that has been done. This car is basically rust free now with the amount of sheet metal work I have done. I do body and paint for a living so the car has been done correctly. There is close to 8k in AMD sheet metal alone.
Project "Pig Pen" 1967 Dart Gt
Additional parts $3,000
440 block
727 trans
BB driveshaft
26 inch Cold case radiator
Stainless trim
2 Very nice tail panels
Multiple sets of tail panel trim
Multiple sets of fender marker lights some NOS
Stainless trim clips (new)
Schumaker BB Tri Y headers chrome with shim kit
Schumaker Slant 6 to RB motor mount kit
67 Dana 8-3/4 Sure grip unit
Stainless rocker moldings with full clip set
Car is located in Janesville Wisconsin 53548
Please message me here if you are interested.
Thanks Fabo.
Roller
This is a major project that I just do not have time for anymore. I am going to put it for sale for 30 days. If it doesn't sell I am going to cut it up and part it out.
I DO NOT have a title for this car. I was going to get one via the Vermont loophole but that has been shut down. I will sell it with a bill of sale to anyone wanting to purchase it.
No build sheet, no fender tag. I have done the DMV search and the car does not show up as stolen or any non sense like that.
I have done a lot of sheet metal work to the car. I am going to try to at least have the sheet metal work finished in the next two weeks. The quarters will not be installed so refinishing will be easier inside the trunk and so forth.
The car is now a roller on a dolly in the front but comes with a lot of parts.
What you will get.
Body
Two hoods
Deck lid
Front and rear seats
Dash
Steering column
K member with front suspension
Grill
Tail lights (not good condition)
Front and rear bumpers with brackets
A/c heater box with all a/c parts that were on the car when I bought it
One extra door I think it is the driver door
All bolts and fasteners that are marked
Any bolt on part that I took off like latches and such
Two front rims with junk tires on ralley wheels No trim rings
I have a TON of parts that will be sold separately from the car. A package deal could be had for everything I had to build the car. This was going to be a 440 car.
Body and above parts $5000
Here is a build thread link to show the metal work that has been done. This car is basically rust free now with the amount of sheet metal work I have done. I do body and paint for a living so the car has been done correctly. There is close to 8k in AMD sheet metal alone.
Project "Pig Pen" 1967 Dart Gt
Additional parts $3,000
440 block
727 trans
BB driveshaft
26 inch Cold case radiator
Stainless trim
2 Very nice tail panels
Multiple sets of tail panel trim
Multiple sets of fender marker lights some NOS
Stainless trim clips (new)
Schumaker BB Tri Y headers chrome with shim kit
Schumaker Slant 6 to RB motor mount kit
67 Dana 8-3/4 Sure grip unit
Stainless rocker moldings with full clip set
Car is located in Janesville Wisconsin 53548
Please message me here if you are interested.
Thanks Fabo.
