I've been restoring a 67 Dart GT since 2014 and finally is is painted and ready for assemble. Will turn out great I hope.
1967 Dart GT
- Thread starter 65dartcharger
- Start date
-
A lady in town that I known for years asked me so I thought yes, I can help but in a way so I still can concentrate on my Dartcharger restoration. Since it is done I have done the front end incl Engine and tranny, the rear end and all the wiring harnesses. Same as my Dartcharger no, it will be a great driver for her. 273/904 and some new Cragars.
I'm thinking of mounting 68 weatherstrip w/moulding instead of the plastic lookstrip. What do you 67 to 69 guys think of the idea? I don't have any experience of these cars!
ScampMike
Despicable Damn Yankee
LOVE the color!!! :twisted:
Alex5280
74' Duster
Awesome!!!
The paint turned out great. The stugf reay for assembly will take some yime.
However still searching for drivers headlight bezel!
However still searching for drivers headlight bezel!
67Dart273
Well-Known Member
That color is already non-factory, so I guess you are not going for "restore correct?" The 68 stuff is what is happening to mine. All you need is to install the clips which are readily available.
Also, you can play with the screws and clips for the dash frame and install them from the bottom. That way, if you ever need / want to rework your dash, you can pull it out of the car easily without dicking with the windshield.
67dartgtgo
Well-Known Member
I updated to the 68 windshield gasket, clips and stainless trim and never looked back.
Great looking ride, by the way....love it.
Great looking ride, by the way....love it.
There is nothing like assembly! Putting back restored or new stuff really gives you a kick!
1969VADart
Well-Known Member
This is pretty close to the color combination I am going for. Very nice car. Mine will hopefully be at this stage in the next couple of weeks.
The part are hetting there! If I just had the left headlight bezel!
The rear bumper and the right tail light in place. Battery tray in place as well as accelerator pedal.
To be continued..
To be continued..
ScampMike
Despicable Damn Yankee
oh - you're having fun!
limelite70
Well-Known Member
- Joined
- Mar 1, 2006
- Messages
- 1,255
- Reaction score
- 42
I smell a hellcat motor goin in.
Well, not really! A 1965 273 2 barrel engine overhauled.:burnout:
Does anyone have a picture of the starter relay and whete it isbplaced?
Thanks FABO
Doeas any FABO member have a blue print or a picture on how the mounting and the routing of the brake lines goes?
Any input is gladly appriciated.
Thanks FABO
Any input is gladly appriciated.
Thanks FABO
The drip mouldings were in bad condition. 3 hours later they were on the car in very good condition. I thought I was done with polishing stainless steel mouldings!!
Found a set of rear bumper brackets too. Found a picture on the web on a propotioming valve. Is this the right model?
Found a set of rear bumper brackets too. Found a picture on the web on a propotioming valve. Is this the right model?
Lookin Great Ulf !! Check my build thread at the bottom of my post. A few pages back, there, I replaced valves and lines on my GTS. Hope that helps.
Thanks Mitch! That was awesome, just what I needed.
desmo900
Well-Known Member
There is some information in this catalog:
http://online.flipbuilder.com/wmmk/wtis/mobile/index.html
Thanks desmo900! Last night I did all the brake line routing and it turned out fine. However I found one "valve" that must have been on the car too. Is this valve for the rear brakes?
Next is to primer the undercarrige!
Next is to primer the undercarrige!
Now the undercarrige is sprayed with grey epoxy primer. Next will be to install engine/tranny and front end setup.
Swinger340Canuc
72 Swinger 340 Special
Great project, that colours got some pop! Wish I was at the stage your at, keep it coming.
-
