1970 Dart Drag Car (Rolling)

-
Status
Not open for further replies.
70Dart499

70Dart499

Well-Known Member
Joined
Apr 8, 2012
Messages
87
Reaction score
2
Location
Plant City
Rating - 0%
0   0   0
Contact seller
1970 Dodge Dart Swinger, actual H code 340 automatic car, currently setup for bigblock and 727. This car is being sold as a complete roller minus motor and transmission.
Rear End: 8 3/4 with 4:11 gears 31 spline Moser axles, and spool.
Ladder Bar Rear suspension, with Afco double adjustable coil over shocks, ladder bars done by Bill Lee Racecars in August of last year, $3000.00 parts and labor.
Front suspension is stock, with new Competition Engineering 90/10 shocks.
Body and paint are about a 7 out of 10 with a few scratches and dents, but not bad for a 40 year old car. Interior is in good shape. 5 gallon fuel cell in trunk, Holley blue pump and regulator, braided steel lines throughout. MSD 6AL Box, Line lock. Car will hook on dirt and is very consistent. Needs, motor, tranny, headers, and radiator and some other small things. I also have a reverse manual valve body bigblock 727 transmission and converter with just over 100 runs on them that I will sell with the car for an additional $500.00. Car is in Plant City FL, has a clear Florida title. I I'm sure there is alot i'm leaving out, so if you have any question or For Additional photos of car, contact me. Thanks Asking $7,500.00 Cash, Cashiers Check or Money Order

100_0816.jpg
 
PM me you E-mail addresses and I will send you some photos, I have quite a few.
 
A68DART360 said:
is the roll bar certifiable and mild steel or chrome moly
Click to expand...

Roll Bars need not be certified since they are only allowed to go 10 flat...anything faster then 9.99 required Certified roll CAGE....
 
70aarcuda said:
Roll Bars need not be certified since they are only allowed to go 10 flat...anything faster then 9.99 required Certified roll CAGE....
Click to expand...
I asked because the side bar looks kind of low where it does not cross between the elbow and shoulder when you are sitting in the seat. I had a tech guy say that about my bar that is in my current car.

Is it a mild steel roll bar.
 
OK, guys somebody make me an offer on this car, I've found another car I want to buy but I need this one gone first. First reasonable offer gets it.
 
Will you sell the BB tranny and converter seperately? If so will you put them on a pallet and take to a shipping house?
 
Wish you were closer and I had some cash. That's something I've been thinking about building.
 
A68DART360 said:
I asked because the side bar looks kind of low where it does not cross between the elbow and shoulder when you are sitting in the seat. I had a tech guy say that about my bar that is in my current car.

Is it a mild steel roll bar.
Click to expand...

Yes you are right about that. They checked mine & I was OK. Even though mine was well within spec.

Is there no side bar on the passenger's side or is it just the angle of the pics?
 
i dont see a side bar for passenger, 11.50 1/4 mile fast need a bar including both side bars elbow to shoulder, most tracks want it up where the back bar behind the seats meet
 
quartermilepass said:
i dont see a side bar for passenger, 11.50 1/4 mile fast need a bar including both side bars elbow to shoulder, most tracks want it up where the back bar behind the seats meet
Click to expand...

Only need a door bar on drivers side to 10.00. Gen regs 20:4:10

Congrats on selling the car.
 
Status
Not open for further replies.
-

Back
Top