63 Dodge Dart, now let me see;)

[George Jets]

Tip for pictures in tight places.

Shoot it in video probably with flash in, then swoop in there at different angles as it is recording.

The go back and watch the video and screen shot out what you want to save as a still picture.

Also in Selfie mode, can give you another refined vantage point to capture pictures.


☆☆☆☆☆

 

[Dne007]

Well, my phone died just as I was taking these pics. maybe gives a better relation from the torsion bar to the end of the Clutch rod end.

Anyway, this is it in the garage until next week, like Wednesday it's all just thinking about possibilities~ I do like more and more about an external slave.

maybe something like this inbetween the exhaust and TO arm. make a nice bracket to hold, then wrap it.

Clutch Slave Cylinder | eBay

Category: Transmission and Transaxle - Automatic > Manual Transmission Components > Clutch Slave Cylinder. Warranty Duration: 1 Year. EXEDY is a Tier 1 OEM supplier to all major automotive, and off-highway manufacturers across the globe.

www.ebay.com

Or this:

https://www.amazon.com/McLeod-Racing-139006-External-Universal/dp/B07DLTDDGL/?tag=fabo03-20

Always good to have another bell housing around

This looks better, I'd have to do my own mods

62-74 MOPAR BIG BLOCK 383-440 BELLHOUSING w/ EXTERNAL HYDRAULIC SLAVE

Big Block Chrysler Aluminum Bellhousing w/ Billet Aluminum Slave Cylinder for Hydraulic Clutch Conversion Application: 1962-74 Chrysler 383-440 & 426 Hemi A, B & E Body; 18 or 23 Spline Trans w/ 130 or 143-Tooth Flywheel SLAVE CYLINDER SPECS; Use with 13/16" Bore x 1" Stroke or .700" Bore x 1.4"...

www.racetuning.com

 

[halfafish]

I wish I knew how far the clutch arm has to travel to disengage.

It looks like you are working with the 833OD trans, is this correct?

 

[Dne007]

Hi Zach;) yes, I do have an A833od

It looks like you are working with the 833OD trans, is this correct?

 

[GGs66GT]

That is 2 1/4” exhaust pipe you are running right.

 

[Dne007]

I've never measured Glen, It's stock pipe that I bought from Ray. ;)

 

[halifaxhops]

1 3/4 I think

 

[halfafish]

Hi Zach;) yes, I do have an A833od

Give a shout on this when you get a minute? No hurry.

 

[Dne007]

ok, had a little time today to do something before leaving for Philly~ engine/trans setup with exhaust, figuring on an external slave cylinder. Zach's helping me out, but all are welcome to voice.
Oh, the large socket represents a slave cylinder going to finish packing now~

Clutch Slave Cylinders

Tuner TS Performance 6-POSITION chip programmer OFFSET SHIFTER SHORT THROW B RB HEMI LS1 LS2 LS3 LS6 tr6060 Hydraulic Clutch FORK RST RXT Twin Disc Flywheel pitman arm Lift Skyjacker MoPar Jeep Wrangler JL Differential Rear End Cover leaf springs a b e body MASTER SLAVE CYLINDER STEEL BRAIDED...

www.racetuning.com

Search ModernDriveline.com

Search our site: Modern Driveline, Inc.

www.moderndriveline.com

I'd have to fabricate my own bracket, but that's ok.

 

[mygasser]

that'll work

 

[Dne007]

I'm looking seriously at this one by Modern driveline, the line going in is at a 90 degree angle and out the side vs out the back. plus it looks shorter, I wish they'd put measurements in their ads. I think I just need
the cylinder and the bracket that it is retained in.