64 and 65 barracudas

-
Status
Not open for further replies.
S

spoolinhard

Active Member
Joined
Mar 15, 2010
Messages
41
Reaction score
3
Rating - 100%
3   0   0
Contact seller
Not alot of body parts good on these cars. They are rusty and they are beat up. The copper one is a slant 6 3 on the tree car, it is complete. The gold one is a 273/4 speed car, most anything useful has been stripped. Mostly what is good is small interior and exterior trim. Between the two cars, I think that the only useable external panels are a decklid, a pass side grill section, and a rear bumper (that needs rechromed). With that being said, these cars are going in for iron so if there is something that you could use, speak up.
DSCN0491.jpg

DSCN0490.jpg

DSCN0488.jpg

DSCN0489.jpg

DSCN0486.jpg
 
One more. I have linkage pedal assemblies and a 4 speed hump for sale in another thread.
DSCN0487.jpg
 
just the passengers side on the copper car. The drivers side has a small crack, and a mounting tab is missing on the center section. All useable but I wouldnt if it was anthing but a driver
 
If no one buys the seats, I need the hinge pins. Just pop the cap off of each under the seat and wiggle the seat back and pull out the pins. i need the pins and the caps. Two sets (8) would be ideal. The wire for the seat adjusters underneat between the runners would be nice. Also, the shift plate, boot, and carpet guard on the four speed. Dash pad would be nice too!


you are in council bluffs, iowa, correct?
 
bamacuda said:
If no one buys the seats, I need the hinge pins. Just pop the cap off of each under the seat and wiggle the seat back and pull out the pins. i need the pins and the caps. Two sets (8) would be ideal. The wire for the seat adjusters underneat between the runners would be nice. Also, the shift plate, boot, and carpet guard on the four speed. Dash pad would be nice too!


you are in council bluffs, iowa, correct?
Click to expand...

The cars are located about 30 mi east of CB in Persia.

I doubt anyone would buy the seats, only one of the four has good foam, I will take a look at the pins and the adjuster wire and see if they are useable. The shift plate, boot are long gone, the pad is shot, and the carpet guard is already spoken for, sorry.
 
I can use the throttle cable and the center link on the v8 barracuda, also is that an 8 track tape in the /6 car?
 
Is the spare tire well any good? Mine is rusted thru. Also, the seat bases would be good if I upgrade to newer seats... just the bases. Rear bumper license plate light. I am sure there is other stuff.
 
38 Dodge said:
I can use the throttle cable and the center link on the v8 barracuda, also is that an 8 track tape in the /6 car?
Click to expand...
Sorry, the center link and the throttle cable are spoken for. yes that is an 8 track, It is very dirty and I HIGHLY doubt that it works. If you want to take a chance on it, PM me and I will pull it for you

Valiant63 said:
Is the spare tire well any good? Mine is rusted thru. Also, the seat bases would be good if I upgrade to newer seats... just the bases. Rear bumper license plate light. I am sure there is other stuff.
Click to expand...
The spare tire wells are shot on both cars. The seat bases are available, out of the 4 buckets, only one has a useable seat bun, I would image that the rear bumper light is there. If you want any of this shoot me a PM
 
what is the condition of the body by the rear quarter windos, I need the area on the 1/4 panel that goes from just behind the door up and around the quarter window. I can get a pic of the area if you need to tell where I am talking about, well, the window trim goes around the windo over the piece I need, the lip on my rotted away


FF
 
Are any front seat chrome backrest sides usable? looking for one set. The Plymouth letters on trunk, lighter in dash, back seat hinge pivot bolts, seat belt retractors, chrome trim on deck behind rear seat, trap door moulding, and are those Craiger wheels available and what is condition.
 
Fstforward said:
what is the condition of the body by the rear quarter windos, I need the area on the 1/4 panel that goes from just behind the door up and around the quarter window. I can get a pic of the area if you need to tell where I am talking about, well, the window trim goes around the windo over the piece I need, the lip on my rotted away


FF
Click to expand...
I should have this, please send me a pic anyway to show me the exact areas that you need.

Dubberd1 said:
Are any front seat chrome backrest sides usable? looking for one set. The Plymouth letters on trunk, lighter in dash, back seat hinge pivot bolts, seat belt retractors, chrome trim on deck behind rear seat, trap door moulding, and are those Craiger wheels available and what is condition.
Click to expand...
PM sent

70DartMike said:
PM sent on radio bezel, heater knobs, gas pedal, and 273 thermostat housing.
Click to expand...
replied


Gold car is getting pretty stripped, Alot of stuff pending, I will post up what is gone when I recieve payment. Also, I think I replied to everybodys PMs, if I didnt please let me know.
thanks
-Kaleb
 
Pending so far:
4 speed hump trim plate
grille
glovebox trim
trunk lettering (both sets)
bellhousing flywheel and shield from 273 car
z bar clutch rod and fender mount from 273 car
cowl and inner fender plugs on both cars
rear window interior uprights (plastic pieces)
v8 center link
v8 gas pedal bracket
seat hinge pins

parts of interest that are still available:
2 sets of 4 spd. pedals
z bar clutch rod and fender mount from slant 6 car
4 speed hump from the 273 car
also the manual drive shaft from the slant 6 car.
 
The following are sold:
cowl plugs
grille
seat hinge pins

I will be pulling the next round of parts tomorrow. Im not sure if I will have enough time to get all of it pulled. I didnt expect there to be this much interest. You guys are running me ragged!
 
Any chance the slant 6 is the actual 1965, if so I'm interested. let me know the engine code number? Also interested in the radio w/knobs if you still got them?
 
Status
Not open for further replies.
-

Back
Top