gregsdart
Well-Known Member
Gen 3 parts
Nib Apache heads, loaded $1200 shipped
Complete intake system , loaded as it came off 485 hp crate motor, zero time on it. $450 shipped
Helcat blower, needs front bearing (typical warrantee problem) $ 1600 shipped
5.7 core motor, eveything but valve covers make offer
Jeep srt8 exhaust manifolds, $400 shipped
Scat 6.2 long sbc hbeam rods frm same 6.1 drag pack motor, 2.1 bearings on rods .927 pins, warm up time only, $230 shipped
Stock dual plug coils from newer 6.1, $80 shipped
Molner 3.888 stroke Gen 3 hemi crank, $600 plus freight
5.7 core motor, eveything but valve covers make offer
Possible package deal
5.9, 5.2 Magnum parts
Standard length Magnum engine stainless steel 2.02 intake valves (already back cut 30* angle), 1.62 exhaust valves, new in box. Springs, retainers, keepers, seals and locks, new, never opened. New, 399 +$30 for back cut, from Hughes, $340 shipped
5.2/5.9 Magnum hydraulic roller cam from Comp, 225 dur at .050 int, 225 dur at .050 ex, 107 lsa, .480 lift. $220 shipped
Small block distributor FBO advance limiting plate and Mr Gasket spring kit, $25 shipped
BB parts
6 2.25 intake valves for 440-1 heads $75
8 2.19 intake valves for 440-1 heads, $120
three sets ball to ball pushrods, one low deck for Jesel , two high deck for Jesel, 3/8, Indy 3/8 heavy wall. Make offer.
One set ball to cup 8.60 length pushrods, make offer.
Rocker shaft retainer kit for Indy 440-1 original rockers $190 (?) from Indy, $100 shipped
Greg
No posting of phone #s or email addresses unless a Gold Member
Nib Apache heads, loaded $1200 shipped
Complete intake system , loaded as it came off 485 hp crate motor, zero time on it. $450 shipped
Helcat blower, needs front bearing (typical warrantee problem) $ 1600 shipped
5.7 core motor, eveything but valve covers make offer
Jeep srt8 exhaust manifolds, $400 shipped
Scat 6.2 long sbc hbeam rods frm same 6.1 drag pack motor, 2.1 bearings on rods .927 pins, warm up time only, $230 shipped
Stock dual plug coils from newer 6.1, $80 shipped
Molner 3.888 stroke Gen 3 hemi crank, $600 plus freight
5.7 core motor, eveything but valve covers make offer
Possible package deal
5.9, 5.2 Magnum parts
Standard length Magnum engine stainless steel 2.02 intake valves (already back cut 30* angle), 1.62 exhaust valves, new in box. Springs, retainers, keepers, seals and locks, new, never opened. New, 399 +$30 for back cut, from Hughes, $340 shipped
5.2/5.9 Magnum hydraulic roller cam from Comp, 225 dur at .050 int, 225 dur at .050 ex, 107 lsa, .480 lift. $220 shipped
Small block distributor FBO advance limiting plate and Mr Gasket spring kit, $25 shipped
BB parts
6 2.25 intake valves for 440-1 heads $75
8 2.19 intake valves for 440-1 heads, $120
three sets ball to ball pushrods, one low deck for Jesel , two high deck for Jesel, 3/8, Indy 3/8 heavy wall. Make offer.
One set ball to cup 8.60 length pushrods, make offer.
Rocker shaft retainer kit for Indy 440-1 original rockers $190 (?) from Indy, $100 shipped
Greg
No posting of phone #s or email addresses unless a Gold Member
Last edited by a moderator:
