Stop in for a cup of coffee

-
goldfish65 said:
Good morning. It's hard to make coffee before you've had your coffee. Took a sip and thought, my taste buds must really be off. Then realized I missed the step of putting in the coffee, it was yesterdays grounds.

Painful night, I was saying every cuss word in the book...a few turns driving the porcelain bus...felt like I couldn't stand it anymore but then I drifted off for 3 hrs and now I think I'm ok. Went and gassed up the Fury, no line at the pump.

Now I have the option of staying with my good friend and his wife in Atlanta. Five hour drive. Five days is a rather long time to be a guest. Or, the original plan, 8 hrs to Sarasota, to visit my Mom. I think Mom wins this one.
Click to expand...
dah - that had to have been nasty!!
DAH - that's even nastier!!!
always opt to see mom if it's an option!!
 
goldfish65 said:
Good morning. It's hard to make coffee before you've had your coffee. Took a sip and thought, my taste buds must really be off. Then realized I missed the step of putting in the coffee, it was yesterdays grounds.

Painful night, I was saying every cuss word in the book...a few turns driving the porcelain bus...felt like I couldn't stand it anymore but then I drifted off for 3 hrs and now I think I'm ok. Went and gassed up the Fury, no line at the pump.

Now I have the option of staying with my good friend and his wife in Atlanta. Five hour drive. Five days is a rather long time to be a guest. Or, the original plan, 8 hrs to Sarasota, to visit my Mom. I think Mom wins this one.
Click to expand...
you're probably lucky that the gross coffee didn't make you sick again... *makes barf face*.... :lol:
 
The first attempt at coffee wasn't all that bad, just tasted like watered-down coffee! Well I better throw some clothes in a bag and get going, before the roads fill up with evacuees.
 
TXDart said:
If no c clips you have bearing retainers on the ends,4" bolt pattern has 4 nuts and 4,5 bolt pattern has 5.they are not pressed in,hope this helps.
Click to expand...
yep, i removed the 4 nuts first thing. still can't budge them.

halifaxhops said:
And do not take the main caps off of the center section until the axels are out. There is nothing on the pin between the spider gears? Take a second look, there has to be something. I had a few that had them also with the "bolt in" axel bearings.
Oh yeah first in!
Click to expand...

main caps are still on. Nothing whatsoever on the pin in the carrier, just a roll pin but the ring gear has to be removed first, I see no way to get the roll pin out other wise.
 
MOPARMITCH said:
Yeah.. Especially Clinton...
Click to expand...

14570348_370957763294186_8208626067656981873_n.jpg
 
goldfish65 said:
The first attempt at coffee wasn't all that bad, just tasted like watered-down coffee! Well I better throw some clothes in a bag and get going, before the roads fill up with evacuees.
Click to expand...
From what I heard, you may be too late on the roads filling up. Stay safe.
 
I am not saying I am for or against Hillary ...I am not saying anything

but that meme with Bill Clinton was just funny. LOL
 
zkx14 said:
I got sheet metal for mine at Anderson Metal in Hallam.
I saw that it is now part of Alro Steel. If still the same guy running it he actually told me he likes to take care of guys like us that just need small orders for projects, cars, whatever...
Click to expand...
halifaxhops said:
That's a hike for him. I was just surprised Fastenall does not sell it, they have a bunch of flat and round stock though......
Click to expand...
Guess it depends what else you can find local. I expect shipping would not be cheap, and if it shows up bent. :( Don't recall the gauges. I got a full sheet for body. He cut it in 3rds to fit in my wagon. also got smaller (few square feet) each of heavier for rockers and similar and heaviest was same as frame rails, brackets, etc. Think I gave a little over $100 for all (several years ago)
 
Got the doors on the GTS the other day. But, been so busy with this and that, I didn't get to adjust them until yesterday. Now I can dig the fenders and hood out of the trailer and finish getting it road worthy...Maybe, tomorrow.. Got a Quikie Radiator and T stat job on 96 Camry this morning.
 
zkx14 said:
Guess it depends what else you can find local. I expect shipping would not be cheap, and if it shows up bent. :( Don't recall the gauges. I got a full sheet for body. He cut it in 3rds to fit in my wagon. also got smaller (few square feet) each of heavier for rockers and similar and heaviest was same as frame rails, brackets, etc. Think I gave a little over $100 for all (several years ago)
Click to expand...
I had a 68 4dr Satty, Parts car for the RR resto I did. After I parted it out, and before I sent it away, I cut the entire roof center out of it. To keep for future sheetmetal repairs , using Ma Mopar Metal.
 
You must log in or register to reply here.
-

Back
Top