Search results for query: *

Some good info here as well: Rebuilding the 5.7L HEMI - Engine Builder Magazine

That appears to be the block heater location.

If you're in Edmonton I can help you get things sorted out as I use the same system in my Dart. It would be easy enough to try my hand held programmer on your setup to see if that's your problem. I also have a spare ECU you can try if it appears to be the problem...

I've picked up a number of connectors (injector, TPS, MAP, IAT, etc.)from these guys: http://www.racetronix.biz/index.asp?url=IND

I went that way a few years ago and it's been working great! There are some pictures posted in this thread: http://www.forabodiesonly.com/mopar/showthread.php?t=181027 The sender I ended up using was for an A-100 van as the variable resistor is located at the top side of the assembly leaving...

I don't know about Manitoba, but in Alberta you need an out of province inspection prior to registering an imported vehicle which is what paragraph 13 is referring to. You will be given the Vehicle Import Form - Form 1 when you clear Canada Customs that you'll need when registering the...

If it's older than 15 years it's exempt from the RIV program. Check the exemptions on this page: http://www.cbsa-asfc.gc.ca/publications/pub/bsf5048-eng.html#s3

I was eating breakfast with my 10-year-old Granddaughter and I asked her, "What day is tomorrow?". Without skipping a beat she said, "It's President's Day!". She's smart, so I asked her "What does President's Day mean?". I was waiting for something about Washington or Lincoln...

I made my own and have been running it for a while now... http://www.forabodiesonly.com/mopar/showthread.php?t=48163 Originally it was running with a carb @6psi but now I have an EZ-EFI system @45psi. The regulator ended up in the engine compartment with a return line to the tank.

The field wires can be interchanged.

You can use a standard Chrysler voltage regulator as in the following diagram.

A couple of pictures of mine...

This is what the pump assembly looks like from the outside: and inside: The connector I used is a Conxall/Switchcraft pn:4182-3SG-300 (mates with Conxall/Switchcraft pn:3182-3PG-3DC). Both are available from Digikey. One pin is used for the sender and the other 2 are for the pump power and...

I've run my in-tank pump for a ~2K miles without any issues (except a cracked float that sank to the bottom of the tank:banghead:) It is very quiet - barely audible without the engine running. My original plan was to run a carb on the 5.7l I was installing and everything was working fine until...

Maybe it could use one of these... The Nut Bra - YouTube

Man who slings mud loses ground.

The room was full of pregnant women with their partners. The class was in full swing. The instructor was teaching the women how to breathe properly and was telling the men how to give the necessary assurance to their partners at this stage of the pregnancy. She said "Ladies, remember that...

Didn't see this posted anywhere here - might be of some interest... http://www.lov2xlr8.no/broch1.html

I also have TTI's (with TTI mounts) and didn't need to modify them. To get an acceptable amount of clearance I also shimmed the driver side engine mount with a 1/4" spacer. Since I used a A518 trans. I built the trans mount to set the engine/trans angle to ~3.5° which may have helped with the...

I used an A518 behind the 5.7l in my '69 Dart. The amount of tunnel mods were minimal - just some minor tweaking for clearance and a new transmission mount. The upper portion of the original rear mount needed to be relocated to the top side of the floor pan for tail shaft / OD clearance. I...

A few more pictures and some dimensions: Left to right: A518, A727, A500 Length and mount dimensions:

2 year Electronics course, 2nd year students have a communications course with a substantial amount of radio testing / trouble shooting... keeps me busy as well!

That's too funny as I've got a 1200 apart on my bench and 2 1200S's waiting for some TLC - students trash them every semester. Never thought I'd see one in this forum!

She got the numbers right!

A man is stopped by the police at midnight and asked where he’s going. “I’m on the way to a lecture about the effects of alcohol abuse on the human body.” The policeman asks, “Really? And who’s going to give a lecture at this time of night?” “My wife...."

Looks kind'a challenging...

Mine gets it's fuel from an in-tank pump that fits though the existing pickup hole. I posted a couple of pictures here: http://www.forabodiesonly.com/mopar/showthread.php?t=48163 I've since changed the pump outlet size to 3/8" and the return to 1/2". The regulator / filter are up front in the...

I'd be interested in a set as well! It would also be cool to have a set that would fit into the recesses of a '69 power bulge molding (~7.625" x 0.5" long) if it can be done for a reasonable price!

Unfortunately Unisteer never released those items. I was told by a company rep that the extra cost of custom headers killed the project.

An Italian, a Scotsman and a Chinese man, are hired at a Construction site. The foreman points out a huge pile of sand. He says to the Italian guy, 'You're in charge of sweeping.' To the Scotsman he says, 'You're in charge of shoveling.' And to the Chinese guy, 'You're in charge of supplies.' He...