Recent content by bobsgtx

  1. B

    Help! No power!

    Voltmeter is best but test light would work. Start at battery with headlights or key or both on and see where you have power and not. Wiring diagram helps.
  2. B

    Which thermostat to go with 185/175 temp sensor?

    On the trucks I worked on with fan clutches the fan would engage 10 degrees above the thermostat. 180 thermostat fan engages at 190 and so on.
  3. B

    Ignition Switch Connector (or pigtail)

    I saw a member on FBBO (JimKueneman) is setting up to make the plastic wire connectors.
  4. B

    moog problem solvers creating problems....

    Just think of how a mechanic/technician back in the day at a dealership working for flat rate did it!
  5. B

    29TH ANNUAL CHRYSLER PERFORMANCE TRADE SHOW AND PARTS SWAP MEET MARCH 1ST & 2ND INDIANAPOLIS, INDIANA

    I'm asking if this is worth a 5 hr. drive each way for me and an overnight?
  6. B

    Bellhousing Experience Quicktime vs Lakewood

    So after reading all the comments I guess you have to check everything when using a Lakewood or Quick Time safety bell housing. Your luck will vary.
  7. B

    Ford 9" in 1965 Barracuda...an option?

    And Don't forget the off road clubs and shops.
  8. B

    Matco Ball Joint Press

    I have used a HF C frame ball joint/universal joint press on three F150"s. For under $100 and all I had to do was to make an additional spacer to pull the new ball joints in all the way.
  9. B

    1/2 inch pick up tube

    Just a stupid question. Why? Unless this is a race, high rpm, large clearance build I would think the stock 3/8' pickup would be sufficient. The machine work to convert to 1/2" tube is usually done with block machining not at final stages. Some additional oil flow can be made by de burring and...
  10. B

    70s Power Wagon Ignition switch info needed !!

    I would start by checking battery voltage while cranking. Then I would do a voltage drop test between the pos. battery and the ignition module while cranking. Then from the neg. battery to the ignition module base that should be grounded to the body. Diagnose before replacing parts.
  11. B

    426 Hemi air cleaner

    There is a guy in MI. that makes bases for carter, edelbrock afb and avs carbs. I think he makes chrome covers also. I think he is on Ebay. You have to wait since he runs batches and bases are different depending on carbs. $1500 is about right for top and bottom.
  12. B

    Need help understanding Mopar ignition…no spark

    Take a new spark plug of any type and open the gap to .080" to .100" on spark plug wire and grounded. Have someone crank engine. If you have a good spark that isn't your problem. If no spark hook it to the coil wire and test again. KD used to make spark testers that look like a spark plug with...
  13. B

    gasoline in 5 gal clear plastic jug, OK or not OK?

    Almost all 91/93 octane around here is no ethanol. There are even a couple of stations that have 87 octane with no ethanol. Yes you pay a price of about 20 to 30 cents a gallon more for the low octane but how much gas do my small engines use? Lawn mower hasn't been started in 3 weeks.
  14. B

    Battery Question

    UPS keeps very accurate fleet records for many years. They change batteries, clutches and other parts before they fail. You hardly ever see a UPS truck broke down on the road. Also with batteries with multiple batteries hooked together you should change them all when one fails or you will be...
  15. B

    Severe voltmeter needle oscillations

    I'm assuming that when the wipers and T.S. quit the heater blower also quits. If so you are loosing power to the ignition controlled fuses in the fuse box. There are 3 fuses off of 1 buss that comes from the ignition switch. It looks like there are 6 fuses in the fuse box. 2 are battery power or...
Back
Top