Probably in this thread.
I will leave tomorrow and I am taking the ValianTrailer full of camping gear and other stuff.. while having some room for things if I buy something large.
Last edited:
1964 Dart Grüne Hölle Road Course/Track Day/AutoX Project
- Thread starter slant six
- Start date
-
I will leave tomorrow and I am taking the ValianTrailer full of camping gear and other stuff.. while having some room for things if I buy something large.
Very cool to see Grüne Hölle today at Carlisle. Nice to meet you, & glad you're back up & running.
Tell your daughter good luck with her business venture.
Tell your daughter good luck with her business venture.
7/17/23:
Well I had made it to Carlisle All Chrysler Nationals and back.
Grüne Hölle Towed ~ 2000# of Trailer and Parts, with firewood and Camping stuff up and down many mountains on the way to Carlisle. I met some new folks and found time to Hike and have dinner with friends as well as Do some proper Mountain Flogging of the car whilst the trailer was detached. Good thing I brought the trailer as I Bought a 40" sign for the garage and I did not have to send it home with a friend.. I was able to take it home myself, as it fit in the ValianTrailer.
My pictures from the Chrysler all Chrysler Nationals 2023 can be found Here
Here is some documentation from my trip:
I Left home Thursday morning so that I could get to Carlisle and not take any interstates while towing. I had a Core 727 Transmission to Sell to A&A so the tongue weight was heavy for my little trailer.
I Stopped for lunch where the Elevation on US 22 was probably the highest, at least on my trip at ~2400 ft near the Allegheny Portage Historic Railroad site.
Then back on the road towards The valleys and Hills.
I forgot how much fun PA Route 994 is from Entrinken to Orbinsonia.. Too bad I had the trailer but it was a blast!
This picture is on PA 164 Which goes over that Green Hill in the horizon.
It is glorious when I encounter these Signs on the up or downside of the mountain, while driving this car.
After a few Hours, I got to Carlisle, dropped off my trans core, and Headed for the Campsite. Shesh.... Always 10° Hotter in the Cumberland valley with ~1000' elevtation drop compared to home near Pittsburgh.
Friday Morning Got into gate 3 before the crowds.. Got the car all cleaned up and ready for the show, then headed to the swap meet to find some stuff that I probably don't actually need, but it's a fun walk.
Friday Nite Decided to cool off with a trip back to the mountains.. Found a nice Hike..
I Chose the Challenging route because I am a dumb *** and thought.... this is cool.
2.1 Miles starting at ~800 ft Elevation and ending at ~1900 ft elevation.
Got to the top and it was all good.
Carlisle is somewhere out there~15 miles away under that cloud on the left.
The Carlisle show has a lot of stuff like this..
And giga tons of 2008-2023 Challengers too.
I took US Route 30 home this time, and when there's a big government sign telling me the elevation, I can't help but stop and take some pictures.
I put ~ 500 more miles on the car and it's mostly good to go. I want to relash the valves again and get it cleaned up for the PVGP countryside tour and some other PVGP Shows this week.
Then out to Ohio for another trailer hauling adventure.
Well I had made it to Carlisle All Chrysler Nationals and back.
Grüne Hölle Towed ~ 2000# of Trailer and Parts, with firewood and Camping stuff up and down many mountains on the way to Carlisle. I met some new folks and found time to Hike and have dinner with friends as well as Do some proper Mountain Flogging of the car whilst the trailer was detached. Good thing I brought the trailer as I Bought a 40" sign for the garage and I did not have to send it home with a friend.. I was able to take it home myself, as it fit in the ValianTrailer.
My pictures from the Chrysler all Chrysler Nationals 2023 can be found Here
Here is some documentation from my trip:
I Left home Thursday morning so that I could get to Carlisle and not take any interstates while towing. I had a Core 727 Transmission to Sell to A&A so the tongue weight was heavy for my little trailer.
I Stopped for lunch where the Elevation on US 22 was probably the highest, at least on my trip at ~2400 ft near the Allegheny Portage Historic Railroad site.
Then back on the road towards The valleys and Hills.
I forgot how much fun PA Route 994 is from Entrinken to Orbinsonia.. Too bad I had the trailer but it was a blast!
This picture is on PA 164 Which goes over that Green Hill in the horizon.
It is glorious when I encounter these Signs on the up or downside of the mountain, while driving this car.
After a few Hours, I got to Carlisle, dropped off my trans core, and Headed for the Campsite. Shesh.... Always 10° Hotter in the Cumberland valley with ~1000' elevtation drop compared to home near Pittsburgh.
Friday Morning Got into gate 3 before the crowds.. Got the car all cleaned up and ready for the show, then headed to the swap meet to find some stuff that I probably don't actually need, but it's a fun walk.
Friday Nite Decided to cool off with a trip back to the mountains.. Found a nice Hike..
I Chose the Challenging route because I am a dumb *** and thought.... this is cool.
2.1 Miles starting at ~800 ft Elevation and ending at ~1900 ft elevation.
Got to the top and it was all good.
Carlisle is somewhere out there~15 miles away under that cloud on the left.
The Carlisle show has a lot of stuff like this..
And giga tons of 2008-2023 Challengers too.
I took US Route 30 home this time, and when there's a big government sign telling me the elevation, I can't help but stop and take some pictures.
I put ~ 500 more miles on the car and it's mostly good to go. I want to relash the valves again and get it cleaned up for the PVGP countryside tour and some other PVGP Shows this week.
Then out to Ohio for another trailer hauling adventure.
Very cool stuff! Really nice pictures too! I know you had a great time. Thanks for sharing this!
I see you got a few pictures of my buddy's 1965 Dodge truck with the Cummins conversion.
7/18/23:
After returning home from Carlisle. I got the car all cleaned and Checked on the valve lash. It seems that I either Have a lifter / pushrod not spinning or a Rocker arm that is not oiling out at the Adjuster screw. It's possible I might have to check on these rocker arms or just swap to stock rockers. We'll see.
I took the car to a local Car cruise tonight it was part of the Pittsburgh Vintage Grandprix "race week" where they have various events and shows all around the local area.
Here are some pictures from the event.
I took the hungry kid out for dinner, while the crowds were coming in and building up.
Then we walked back to the show where she was peddling her wares to the locals.
A few interesting notes.. since this is a local show near the town where I grew up, there were some Vehicles that My dad either had owned in his "personal collection" or sold at the car lot.
This 1933 Dodge Five Window Street Rod Sat around the house or garage since 1984 or so...
New owner is enjoying it and actually using it.
We parked next to a 1968 Dodge Dart GT that was sold off dad's car lot about 25 years ago. Same Owner has had it since he bought it off my dd in the late '90's
Tomorrow I will investigate the Rocker arm issue a bit more and swap to stock rockers if needed, or check for obstructions / drill an oil squirt hole on the chunky rockers if needed.
Oh yeah, remember this idea:
IT WORKS!
I have been taking the car hard around some Right Hand turns and no gas dribbling onto the quarter panel any more, so that is good. I just have to open the trunk and the valve when fueling up, but that is not a problem.
Planning on running the PVGP Countryside Tour Thursday.
After returning home from Carlisle. I got the car all cleaned and Checked on the valve lash. It seems that I either Have a lifter / pushrod not spinning or a Rocker arm that is not oiling out at the Adjuster screw. It's possible I might have to check on these rocker arms or just swap to stock rockers. We'll see.
I took the car to a local Car cruise tonight it was part of the Pittsburgh Vintage Grandprix "race week" where they have various events and shows all around the local area.
Here are some pictures from the event.
I took the hungry kid out for dinner, while the crowds were coming in and building up.
Then we walked back to the show where she was peddling her wares to the locals.
A few interesting notes.. since this is a local show near the town where I grew up, there were some Vehicles that My dad either had owned in his "personal collection" or sold at the car lot.
This 1933 Dodge Five Window Street Rod Sat around the house or garage since 1984 or so...
New owner is enjoying it and actually using it.
We parked next to a 1968 Dodge Dart GT that was sold off dad's car lot about 25 years ago. Same Owner has had it since he bought it off my dd in the late '90's
Tomorrow I will investigate the Rocker arm issue a bit more and swap to stock rockers if needed, or check for obstructions / drill an oil squirt hole on the chunky rockers if needed.
Oh yeah, remember this idea:
IT WORKS!
I have been taking the car hard around some Right Hand turns and no gas dribbling onto the quarter panel any more, so that is good. I just have to open the trunk and the valve when fueling up, but that is not a problem.
Planning on running the PVGP Countryside Tour Thursday.
Yep, No Problem!
Yep, Cool stuff there. everyone likes a good 6BT or 4BT in those old trucks. I have seen a bunch of them.
Richard Sweet
Well-Known Member
How does the gas tank vent with the fill line valve closed?
I added a T and an extra vent line on the bottom side of the fill valve for venting.
It is not in those pictures however.
7/21/23:
I participated in the PVGP Coutryside Tour yesterday.
It was ~120 Miles of Heavy Flogging on Wesmoreland, Fayette and Somerset County PA Back Roads and Mountain Routes.
I was a group leader, and the fantastic volunteer organisers of the event thought that the lowly '64 Dart Grüne Hölle Edition should lead off the fastest group first at 9:00 AM.
I had 4 Cars in my Group, all capable European Grand Tourers in their own right.
In my group:
2015 Porsche 991:
1995 Porsche Porsche 995:
1990 Porsche 964:
and a 1990 Mercedes-Benz 500SL
We had a blast ripping around some mountain roads and I made some new friends from Philadelphia and Delaware, it is usually unlikely that Porsche Guys were digging the Dart but they did.
This tour gets a way different crowd than the local car show car cruise guys which is refreshing.
It's safe to say that the engine is fully operating properly and spent much of the time between the 3500-5200 RPM range. Lots of Heel toeing and bliping of the the throttle for downshifts makes me smile, puts the engine in the proper RPM range to get torque coming out of any corner. 95 Mph Maximum Speed on routes that had no freeway or highway in sight.
2 days ago, I swapped what I call the "chunky" Roller Rockers out for stock Slant 6 Rockers.
I had Ran these "chunkies" for a few years with apparently no issues, but not now.
There is a lack of oil at the Rocker adjustment Screw. It was eating up Rocker screws because they were dry. That is why my lash needed reset a few times in the last 3 weeks. The solution there is to Install a Spray Bar in the Valve cover or Modify the Rockers for Adjuster screw oiling - Which is probably what I will do.
After I Left for the Trip, I realized that the Rocker arm Swap back to stock arms was causing some interference issues with the valve cover. (the vales on this head must be a bit taller than stock. I Had a bit of a diaper on the Valve cover during the Countryside tour to catch any oil that was getting ejected out of the car during driving, and for now until I can get some time to do proper cleaning, welding and metal work on this Valve cover I have the Side of the road / parts store hack..
On the #6 where the Valve cover is slimmed down for the Heater box clearance on '60-62 Models the Rockers were knocking and wore a hole through the metal.
This is also happening on the inside too as I can feel the Rockers clicking against the steel metal baffle inside above cylinders 5 and 1/ 2 where the PCV and Oil Fill is.
Quick fix for now:
' till next time.
I participated in the PVGP Coutryside Tour yesterday.
It was ~120 Miles of Heavy Flogging on Wesmoreland, Fayette and Somerset County PA Back Roads and Mountain Routes.
I was a group leader, and the fantastic volunteer organisers of the event thought that the lowly '64 Dart Grüne Hölle Edition should lead off the fastest group first at 9:00 AM.
I had 4 Cars in my Group, all capable European Grand Tourers in their own right.
In my group:
2015 Porsche 991:
1995 Porsche Porsche 995:
1990 Porsche 964:
and a 1990 Mercedes-Benz 500SL
We had a blast ripping around some mountain roads and I made some new friends from Philadelphia and Delaware, it is usually unlikely that Porsche Guys were digging the Dart but they did.
This tour gets a way different crowd than the local car show car cruise guys which is refreshing.
It's safe to say that the engine is fully operating properly and spent much of the time between the 3500-5200 RPM range. Lots of Heel toeing and bliping of the the throttle for downshifts makes me smile, puts the engine in the proper RPM range to get torque coming out of any corner. 95 Mph Maximum Speed on routes that had no freeway or highway in sight.
2 days ago, I swapped what I call the "chunky" Roller Rockers out for stock Slant 6 Rockers.
I had Ran these "chunkies" for a few years with apparently no issues, but not now.
There is a lack of oil at the Rocker adjustment Screw. It was eating up Rocker screws because they were dry. That is why my lash needed reset a few times in the last 3 weeks. The solution there is to Install a Spray Bar in the Valve cover or Modify the Rockers for Adjuster screw oiling - Which is probably what I will do.
After I Left for the Trip, I realized that the Rocker arm Swap back to stock arms was causing some interference issues with the valve cover. (the vales on this head must be a bit taller than stock. I Had a bit of a diaper on the Valve cover during the Countryside tour to catch any oil that was getting ejected out of the car during driving, and for now until I can get some time to do proper cleaning, welding and metal work on this Valve cover I have the Side of the road / parts store hack..
On the #6 where the Valve cover is slimmed down for the Heater box clearance on '60-62 Models the Rockers were knocking and wore a hole through the metal.
This is also happening on the inside too as I can feel the Rockers clicking against the steel metal baffle inside above cylinders 5 and 1/ 2 where the PCV and Oil Fill is.
Quick fix for now:
' till next time.
I love this! Porsche, Porsche, Porsche, Benz, DART. LOL What are you thinkin about for the fix for the valve cover?
Welding. I Will kick it up a bit Higher. I have done this before for other projects. Just need some scrap steel and break out the hot glue gun.
Is the current set-up with the Webers from #302 or the Clifford/4B from #316? Either way, I love the car!
Curre
Thanks!
It does not have the Weber style injection on it yet. It has the single four barrel for now.
Thanks!
Richard Sweet
Well-Known Member
Do you still have this car? Anything new? I see that you've been driving the wagon.
Hello, Thanks for checking in.
Yes, I still have the car. This is the most exciting one to drive in my fleet. I don't think I will be selling it for at least 40 years if things remain as they are.
I have not updated here, because I have not done anything with it. Parts cars, shows,, work, vacation, and family have been demanding my time.
I went on a trip last July 2023 from Irwin, PA to Greenwood, Ohio towing a U haul Single axle Box trailer with the Grüne Hölle Dart. I met up with a buddy to do some slanted discussions and to pick up slanted parts and a Flow bench in Greenwood Ohio, Also on the way home outside of Columbus, I picked up a Slant 6 core engine.
Well Long story short, I had to keep adjusting the valve lash.. found that a cam lobe was wiping away somehow.. Drove it back over 250 miles to PA slowly on 5 cylinders towing a trailer full of parts and stuff.
I started tearing into the '62 Wagon in October of 2023. I try to only work on one thing at a time, as my brain would explode if I had multiple projects going on. I hope to get back on this car in the fall or winter, as it is such a blast to drive. It puts my V8 Stuff and other seemingly well-sorted slant 6 rides to shame in a hurry!
Yes, I still have the car. This is the most exciting one to drive in my fleet. I don't think I will be selling it for at least 40 years if things remain as they are.
I have not updated here, because I have not done anything with it. Parts cars, shows,, work, vacation, and family have been demanding my time.
I went on a trip last July 2023 from Irwin, PA to Greenwood, Ohio towing a U haul Single axle Box trailer with the Grüne Hölle Dart. I met up with a buddy to do some slanted discussions and to pick up slanted parts and a Flow bench in Greenwood Ohio, Also on the way home outside of Columbus, I picked up a Slant 6 core engine.
Well Long story short, I had to keep adjusting the valve lash.. found that a cam lobe was wiping away somehow.. Drove it back over 250 miles to PA slowly on 5 cylinders towing a trailer full of parts and stuff.
I started tearing into the '62 Wagon in October of 2023. I try to only work on one thing at a time, as my brain would explode if I had multiple projects going on. I hope to get back on this car in the fall or winter, as it is such a blast to drive. It puts my V8 Stuff and other seemingly well-sorted slant 6 rides to shame in a hurry!
Last edited:
mygasser
Well-Known Member
had you considered stacking 2 valve cover gaskets for the little extra clearance you need? just superglue them together and then to the valve cover so they stay in line for a leak free fit.
neil.
neil.
That is sure a reasonable solution, but I like the fuss free welding approach. My welding will not get nasty, ripped torn or mis-shaped on the side of the road when adjusting the valve lash. The double gaskets might.
-
